Листовка для Revolabs FLX2 POTS 10-FLX2-101-POTS-04-03
Модели
10-FLX2-101-POTS-04-03
Revolabs FLX2
TM
– Quick Setup Guide
Congratulations on your purchase of the Revolabs FLX2
TM
Wireless Conference Phone. This
system utilizes state of the art technology providing high bandwidth audio and enabling clear,
reliable, untethered communications with your telephone, PC, mobile device, and video
conferencing system.
reliable, untethered communications with your telephone, PC, mobile device, and video
conferencing system.
The Revolabs FLX2 Conference Phone provides enhanced freedom for telephone and video
conferences by allowing independent locations of the microphones and the speaker during the
call.
conferences by allowing independent locations of the microphones and the speaker during the
call.
Unpacking
Your Revolabs FLX2™ Conference Phone
package contains the following items. When
unpacking the system be sure to take inventory
of all parts to ensure that nothing is missing. If
parts are missing, please contact your retailer.
Revolabs FLX2 Conference Phone components
are partially charged. Please charge the
Speaker, the Microphones, and the Dialer for at
least 8 hours or overnight before using the
system.
The Revolabs FLX2 Conference Phone comes
with two different power supplies. Please
ensure that you use the correct power supply
when connecting the Base Station and the
Charger Base.
Contents
FLX2 Base Station
FLX2 Charger Base
FLX Speaker
FLX Dialer
2 FLX Microphones (lapel – omni –
directional microphone shown)
directional microphone shown)
12-15V AC adapter for the Charger Base
5 V AC adapter for the Base Station
RJ11 Telephone Cable
Connecting the Base Station
Place the Base Station close to the analog telephone outlet you want to
use for the conference phone.
Connect the Base Station to the telephone network using the provided
RJ 11 Telephone cable.
Use the 5 Volt power supply to connect the Base Station to the power
outlet. The Base Station will power up.
use for the conference phone.
Connect the Base Station to the telephone network using the provided
RJ 11 Telephone cable.
Use the 5 Volt power supply to connect the Base Station to the power
outlet. The Base Station will power up.
Connecting the Charger Base
Place the Charger Base at a location where you can easily access the
Microphones and the Speaker for your conference calls, e.g. on a side
board, a desk, or the conference table.
Connect the Charger Base to the power outlet using the provided 12-15V
power supply.
Place the Speaker, the Microphones, and the Dialer in the respective
openings of the Charger Base to charge them.
The Dialer and Speaker will automatically connect to the Base Station
after a short time if it is powered up. You will hear a confirmation chime
from the Speaker once the system is ready for use. The Microphones
only connect when taking out of the Charger Base, or if the multi-function
button is pressed while in the Charger Base. If the Speaker or the Dialer
are not powered up, take them out of the Charger Base for a few
seconds and put them back in. This will switch on the component.
Microphones and the Speaker for your conference calls, e.g. on a side
board, a desk, or the conference table.
Connect the Charger Base to the power outlet using the provided 12-15V
power supply.
Place the Speaker, the Microphones, and the Dialer in the respective
openings of the Charger Base to charge them.
The Dialer and Speaker will automatically connect to the Base Station
after a short time if it is powered up. You will hear a confirmation chime
from the Speaker once the system is ready for use. The Microphones
only connect when taking out of the Charger Base, or if the multi-function
button is pressed while in the Charger Base. If the Speaker or the Dialer
are not powered up, take them out of the Charger Base for a few
seconds and put them back in. This will switch on the component.