Справочник Пользователя для IBM Flex System V7000 Expansion Enclosure 4939H29
Модели
4939H29
8068ch13-Maintenance and Troubleshooting.fm
Draft Document for Review January 29, 2013 12:52 pm
528
IBM Flex System V7000 Storage Node Introduction and Implementation Guide
Table 13-5 Node canister battery LED states
5. Table 13-6 describes the SAS port status and activity LEDs, canister activity LED, and
identify LEDs on the canisters.
Table 13-6 Node canister SAS port and control enclosure LED states
LED
layout
layout
LED Name
Color
States
Battery Status
Green
OFF – Indicates the battery is not in a state where it can support a
save of cache and system state data. This is an error condition. Refer
to the battery fault LED and the node status provided by the service
assistant for further information.
save of cache and system state data. This is an error condition. Refer
to the battery fault LED and the node status provided by the service
assistant for further information.
ON SOLID – Indicates the battery is fully charged and can support a
save of cache and system state data. This is the normal state.
save of cache and system state data. This is the normal state.
BLINK – Indicates the battery is charging and can support at least one
save of cache and system state data. No action is required; the node
canister can function as an active member of the system in this state.
save of cache and system state data. No action is required; the node
canister can function as an active member of the system in this state.
FAST BLINK – Indicates the battery is charging, but cannot yet
support a save of cache and system state data. The node canister
cannot operate as an active member of the system in this state. No
action is required; when there is sufficient charge to save the cache
and system state data, the node canister automatically becomes active
in the system.
support a save of cache and system state data. The node canister
cannot operate as an active member of the system in this state. No
action is required; when there is sufficient charge to save the cache
and system state data, the node canister automatically becomes active
in the system.
Battery fault
Amber
OFF – No faults have detected with the battery
ON SOLID – A fault has been detected with the battery. The battery
needs to be replaced.
needs to be replaced.
Attention: If your system is powered on and performing I/O
operations, go to the management GUI and follow the fix procedures.
Removing a node without the assistance of the fix procedures can
result in loss of data or access to data.
operations, go to the management GUI and follow the fix procedures.
Removing a node without the assistance of the fix procedures can
result in loss of data or access to data.
BLINK – The battery has been identified by user action.
Battery in use
Green
OFF – The battery is not providing power to the node canister. This is
the normal state
the normal state
FAST BLINK – The system is currently in the process of saving cache
and system state data to its internal storage device using battery
power. Do not remove, or perform any other service action on the
canister until the LED stops blinking. If the LED continues to fast blink
for more than fifteen minutes, perform the following actions:
and system state data to its internal storage device using battery
power. Do not remove, or perform any other service action on the
canister until the LED stops blinking. If the LED continues to fast blink
for more than fifteen minutes, perform the following actions:
–
Re-seat the node canister.
–
Re-seat the battery in the node canister.
–
Replace the battery.
–
Replace the node canister.
5
6
7
LED
layout
layout
LED Name
Color
States
SAS port
status
status
Amber
OFF – There are no reported faults on the SAS link. This is the normal
state.
state.
ON SOLID – There is no connectivity on the link
SLOW BLINK – The port has been disabled and will not service SAS
traffic
traffic
BLINK – One or more of the narrow ports of the wide SAS port link
have failed, the port is not operating at full capacity.
have failed, the port is not operating at full capacity.
If the LED is not OFF, use the IBM Flex System V7000 management GUI,
if available, and use event log fix procedures to troubleshoot. These
procedures verify that the SAS cable is seated correctly at each end, it is
working, or if one of the canisters it connects to needs to be replaced.
if available, and use event log fix procedures to troubleshoot. These
procedures verify that the SAS cable is seated correctly at each end, it is
working, or if one of the canisters it connects to needs to be replaced.
1