Справочник Пользователя для Alcatel-Lucent OAW-IAP115
2
Alcatel-Lucent OmniAccess 110 Series Access Points
ALCATEL-LUCENT ENTERPRISE
DATA SHEET
Operating modes
The 110 series of APs offer a choice of
operating modes to meet unique manage-
ment and deployment requirements.
operating modes to meet unique manage-
ment and deployment requirements.
• Controller-managed mode. When managed
by OmniAccess controllers, 110 series
APs offer centralized configuration, data
encryption, policy enforcement and
network services, as well as distributed
and centralized traffic forwarding.
APs offer centralized configuration, data
encryption, policy enforcement and
network services, as well as distributed
and centralized traffic forwarding.
• Alcatel-Lucent Instant™ mode. In
Instant mode, a single AP automatically
distributes the network configuration to
other Instant APs in the WLAN. Simply
power up one Instant AP, configure it over
the air, and plug in the other APs — the
entire process takes about five minutes.
distributes the network configuration to
other Instant APs in the WLAN. Simply
power up one Instant AP, configure it over
the air, and plug in the other APs — the
entire process takes about five minutes.
If WLAN and network requirements
change, a built-in migration path allows
110 series Instant APs to become part of
a WLAN that is centrally managed by a
mobility controller.
change, a built-in migration path allows
110 series Instant APs to become part of
a WLAN that is centrally managed by a
mobility controller.
• 802.11a/b/g/n controllerless Instant AP
• 802.11a/b/g/n mobility controller
• 802.11a/b/g/n mobility controller
managed AP
• Remote AP (RAP)
• Spectrum analysis identifies sources of
• Spectrum analysis identifies sources of
RF interference
• Air monitor provides wireless intrusion
protection
• Hybrid AP serves Wi-Fi clients and
provides wireless intrusion protection
and spectrum analysis
and spectrum analysis
• Secure enterprise mesh
Security
• With an OpenDNS service subscription
OmniAccess Instant RAPs deliver
integrated web filtering, malware and
botnet protection to every device
connected to the WLAN.
integrated web filtering, malware and
botnet protection to every device
connected to the WLAN.
• Integrated Trusted Platform Module (TPM)
for secure storage of credentials and keys
• SecureJack-capable for secure tunneling
of wired Ethernet traffic
Wireless radio specifications
• AP type: Indoor, dual radio, 5 GHz and
2.4 GHz 802.11n 3x3:3
• Software-configurable dual radio supports
5 GHz (Radio 0) and 2.4 GHz (Radio 1)
• 3x3 MIMO with three spatial streams and
up to 450 Mb/s wireless data rate
• Supported frequency bands (country-
specific restrictions apply):
¬ 2.4000 GHz to 2.4835 GHz
¬ 5.150 GHz to 5.250 GHz
¬ 2.4000 GHz to 2.4835 GHz
¬ 5.150 GHz to 5.250 GHz
¬ 5.250 GHz to 5.350 GHz
¬ 5.470 GHz to 5.725 GHz
¬ 5.725 GHz to 5.850 GHz
¬ 5.470 GHz to 5.725 GHz
¬ 5.725 GHz to 5.850 GHz
• Available channels: Dependent on
configured regulatory domain
• Dynamic frequency selection (DFS)
optimizes the use of available RF spectrum
• Supported radio technologies:
¬ 802.11b: Direct sequence spread
spectrum (DSSS)
¬ 802.11a/g/n: Orthogonal frequency
division multiplexing (OFDM)
• Supported modulation types:
¬ 802.11b: BPSK, QPSK, CCK
¬ 802.11a/g/n: BPSK, QPSK, 16 QAM,
¬ 802.11a/g/n: BPSK, QPSK, 16 QAM,
64 QAM
• Transmit power: Configurable in
increments of 0.5 dBm
• Maximum (aggregate, conducted total)
transmit power (limited by local regulatory
requirements):
¬ 2.4 GHz band: +28 dBm (23 dBm
requirements):
¬ 2.4 GHz band: +28 dBm (23 dBm
per chain)
¬ 5 GHz band: +25 dBm (20 dBm
per chain)
• ACC minimizes interference from
LTE cellular networks
• Maximum ratio combining (MRC) for
improved receiver performance
• Cyclic delay/shift diversity (CDD/CSD)
for improved downlink RF performance
• Short guard interval for 20 MHz and
40 MHz channels
• Space-time block coding (STBC) for
increased range and improved reception
• Low-density parity check (LDPC) for
high-efficiency error correction and
increased throughput
increased throughput
• Supported data rates (Mb/s):
¬ 802.11b: 1, 2, 5.5, 11
¬ 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
¬ 802.11n: 6.5 to 450 (MCS0 to MCS23)
¬ 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
¬ 802.11n: 6.5 to 450 (MCS0 to MCS23)
• 802.11n high-throughput (HT) support:
HT 20/40
• 802.11n packet aggregation: A-MPDU,
A-MSDU
Power
• Maximum power consumption: 13 W,
plus up to 2.5 W for attached USB device
• Power sources sold separately
• Direct DC source: 12 V DC nominal, +/-5%
• Power over Ethernet (PoE): 48 V DC
• Direct DC source: 12 V DC nominal, +/-5%
• Power over Ethernet (PoE): 48 V DC
(nominal) 802.3af or 802.3at-compliant
source
¬ USB host port is disabled when using
source
¬ USB host port is disabled when using
an 802.3af PoE power source. For
unrestricted operation with PoE power,
use an 802.3at-compliant source.
unrestricted operation with PoE power,
use an 802.3at-compliant source.
Antennas
• OAW-AP114: Three RP-SMA connectors
for external dual-band antennas. Internal
loss between radio interface and external
antenna connectors (due to diplexing
circuitry): 1.5 dB in 2.4 GHz and 2.5 dB
in 5 GHz
loss between radio interface and external
antenna connectors (due to diplexing
circuitry): 1.5 dB in 2.4 GHz and 2.5 dB
in 5 GHz
• OAW-AP115: Six integrated
omnidirectional down-tilt antennas for
3x3 MIMO with maximum antenna gain
of 4.5 dBi in 2.4 GHz and 5.5 dBi in 5 GHz.
Built-in antennas are optimized for
horizontal ceiling mounted orientation
of AP115.
3x3 MIMO with maximum antenna gain
of 4.5 dBi in 2.4 GHz and 5.5 dBi in 5 GHz.
Built-in antennas are optimized for
horizontal ceiling mounted orientation
of AP115.
Other interfaces
• 10/100/1000Base-T Ethernet network
interface (RJ-45)
¬ Auto-sensing link speed and medium
¬ Auto-sensing link speed and medium
dependent interface/medium dependent
interface crossover (MDI/MDIX)
interface crossover (MDI/MDIX)
¬ 802.3az Energy Efficient Ethernet (EEE)
¬ PoE-PD: 48 V DC 802.3af PoE or 802.3at
¬ PoE-PD: 48 V DC 802.3af PoE or 802.3at
PoE+
• DC power interface, accepts 1.7/4.0 mm
center-positive circular plug with 9.5 mm
length
length
• USB 2.0 host interface (Type A connector)
• Serial console interface (RJ-45, TTL levels)
• Visual indicators (LEDs):
• Serial console interface (RJ-45, TTL levels)
• Visual indicators (LEDs):
¬ Power/system status
¬ Ethernet link status (ENET)
¬ Radio status (2x; RAD0, RAD1)
¬ Ethernet link status (ENET)
¬ Radio status (2x; RAD0, RAD1)
• Kensington security slot
• Reset button
• Reset button
Mounting
• Included with AP:
¬ Mounting brackets (2) for attaching to
9/16 in. or 15/16 in. T-bar drop-tile
ceiling
ceiling
• Optional mounting kits:
¬ OAW-AP220-MNTC2: OmniAccess™
AP220 Series Access Point Mount Kit
(ceiling grid) contains 2x ceiling grid rail
adapters (for Interlude and Silhouette
style rails).
(ceiling grid) contains 2x ceiling grid rail
adapters (for Interlude and Silhouette
style rails).
¬ OAW-AP220-MNTW1: OmniAccess
AP220 Series Access Point Mount Kit
(basic, flat surface) contains 1x flat
surface wall/ceiling mount bracket.
(basic, flat surface) contains 1x flat
surface wall/ceiling mount bracket.
¬ OAW-AP220-MNTW2: OmniAccess
AP220 Series Access Point Mount Kit
(box style, secure, flat surface) contains
1x flat surface wall/ceiling secure
mount cradle.
(box style, secure, flat surface) contains
1x flat surface wall/ceiling secure
mount cradle.