Справочник Пользователя для Alcatel-Lucent OAW-IAP114

2

Alcatel-Lucent OmniAccess 110 Series Access Points

The 110 series of APs offer a choice of 
operating modes to meet unique manage-
ment and deployment requirements.

•  Controller-managed mode. When managed

by OmniAccess controllers, 110 series 
APs offer centralized configuration, data 
encryption, policy enforcement and 
network services, as well as distributed 
and centralized traffic forwarding. 

•  Alcatel-Lucent Instant™ mode. In

Instant mode, a single AP automatically 
distributes the network configuration to 
other Instant APs in the WLAN. Simply 
power up one Instant AP, configure it over 
the air, and plug in the other APs — the 
entire process takes about five minutes.

If WLAN and network requirements 
change, a built-in migration path allows 
110 series Instant APs to become part of 
a WLAN that is centrally managed by a 
mobility controller.

•  802.11a/b/g/n controllerless Instant AP
•  802.11a/b/g/n mobility controller

managed AP

•  Remote AP (RAP)
•  Spectrum analysis identifies sources of  

RF interference

•  Air monitor provides wireless intrusion

protection

•  Hybrid AP serves Wi-Fi clients and

provides wireless intrusion protection  
and spectrum analysis

•  Secure enterprise mesh

•  With an OpenDNS service subscription

OmniAccess Instant RAPs deliver 
integrated web filtering, malware and 
botnet protection to every device 
connected to the WLAN.

•  Integrated Trusted Platform Module (TPM)

for secure storage of credentials and keys

•  SecureJack-capable for secure tunneling  

of wired Ethernet traffic

•  AP type: Indoor, dual radio, 5 GHz and  

2.4 GHz 802.11n 3x3:3

•  Software-configurable dual radio supports

5 GHz (Radio 0) and 2.4 GHz (Radio 1)

•  3x3 MIMO with three spatial streams and

up to 450 Mb/s wireless data rate

•  Supported frequency bands (country-

specific restrictions apply):
¬ 2.4000 GHz to 2.4835 GHz
¬ 5.150 GHz to 5.250 GHz

¬ 5.250 GHz to 5.350 GHz
¬ 5.470 GHz to 5.725 GHz
¬ 5.725 GHz to 5.850 GHz

•  Available channels: Dependent on

configured regulatory domain

•  Dynamic frequency selection (DFS)

optimizes the use of available RF spectrum

•  Supported radio technologies:

¬ 802.11b: Direct sequence spread 

spectrum (DSSS)

¬ 802.11a/g/n: Orthogonal frequency 

division multiplexing (OFDM)

•  Supported modulation types:

¬ 802.11b: BPSK, QPSK, CCK
¬ 802.11a/g/n: BPSK, QPSK, 16 QAM,  

64 QAM

•  Transmit power: Configurable in

increments of 0.5 dBm

•  Maximum (aggregate, conducted total)

transmit power (limited by local regulatory 
requirements):
¬ 2.4 GHz band: +28 dBm (23 dBm  

per chain)

¬ 5 GHz band: +25 dBm (20 dBm  

per chain)

•  ACC minimizes interference from  

LTE cellular networks

•  Maximum ratio combining (MRC) for

improved receiver performance

•  Cyclic delay/shift diversity (CDD/CSD)  

for improved downlink RF performance

•  Short guard interval for 20 MHz and  

40 MHz channels

•  Space-time block coding (STBC) for

increased range and improved reception

•  Low-density parity check (LDPC) for  

high-efficiency error correction and 
increased throughput

•  Supported data rates (Mb/s):

¬ 802.11b: 1, 2, 5.5, 11
¬ 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
¬ 802.11n: 6.5 to 450 (MCS0 to MCS23)

•  802.11n high-throughput (HT) support:  

HT 20/40

•  802.11n packet aggregation: A-MPDU,

A-MSDU

•  Maximum power consumption: 13 W,  

plus up to 2.5 W for attached USB device

•  Power sources sold separately
•  Direct DC source: 12 V DC nominal, +/-5%
•  Power over Ethernet (PoE): 48 V DC

(nominal) 802.3af or 802.3at-compliant 
source
¬ USB host port is disabled when using

an 802.3af PoE power source. For 
unrestricted operation with PoE power, 
use an 802.3at-compliant source.

•  OAW-AP114: Three RP-SMA connectors

for external dual-band antennas. Internal 
loss between radio interface and external 
antenna connectors (due to diplexing 
circuitry): 1.5 dB in 2.4 GHz and 2.5 dB  
in 5 GHz

•  OAW-AP115: Six integrated

omnidirectional down-tilt antennas for 
3x3 MIMO with maximum antenna gain  
of 4.5 dBi in 2.4 GHz and 5.5 dBi in 5 GHz. 
Built-in antennas are optimized for 
horizontal ceiling mounted orientation  
of AP115.

•  10/100/1000Base-T Ethernet network

interface (RJ-45)
¬ Auto-sensing link speed and medium 

dependent interface/medium dependent 
interface crossover (MDI/MDIX)

¬ 802.3az Energy Efficient Ethernet (EEE)
¬ PoE-PD: 48 V DC 802.3af PoE or 802.3at 

PoE+

•  DC power interface, accepts 1.7/4.0 mm

center-positive circular plug with 9.5 mm 
length

•  USB 2.0 host interface (Type A connector)
•  Serial console interface (RJ-45, TTL levels)
•  Visual indicators (LEDs):

¬ Power/system status
¬ Ethernet link status (ENET)
¬ Radio status (2x; RAD0, RAD1)

•  Kensington security slot
•  Reset button

•  Included with AP:

¬ Mounting brackets (2) for attaching to 

9/16 in. or 15/16 in. T-bar drop-tile 
ceiling

•  Optional mounting kits:

¬ OAW-AP220-MNTC2: OmniAccess™ 

AP220 Series Access Point Mount Kit 
(ceiling grid) contains 2x ceiling grid rail 
adapters (for Interlude and Silhouette 
style rails).

¬ OAW-AP220-MNTW1: OmniAccess 

AP220 Series Access Point Mount Kit 
(basic, flat surface) contains 1x flat 
surface wall/ceiling mount bracket.

¬ OAW-AP220-MNTW2: OmniAccess 

AP220 Series Access Point Mount Kit 
(box style, secure, flat surface) contains 
1x flat surface wall/ceiling secure  
mount cradle.