Справочник Пользователя для Led Lenser H7.2 7397

02

English 

 Page 02-04

GB

We are delighted that you have purchased one 

of our products.

These are usage instructions to help you 

familiarize yourself with your new purchase. 

All the documents accompanying the product 

must be read attentively before using the 

product, stored for future use and if the product 

is transferred to a third party, the documents 

should be handed over as well. This ensures 

that maximum benefit is drawn from the product 

and questions from users can be resolved when 

they arise.

Above all, comply with the warnings and safety 

instructions and dispose of the packaging 

material properly.

Additional information for H7.2 with “TEST IT” 

function

Your LED LENSER H7.2 headlamp is packaged 

with a “TEST IT” function (item no. 7397). This 

allows users to test the brightness while the 

product is still in the package. For testing, 

simply push the yellow “TEST IT” button on the 

front of the package. When testing, please do 

not look directly into the light.

The “TEST IT” button is connected to the battery 

housing of the H7.2 via two wires and should be 

removed prior to use.  

To remove the “TEST IT” button and wires, 

open the battery box and remove the 4 x AAA 

batteries (see also “Changing Alkaline Batteries” 

further below).  Separate the two “TEST IT” 

button wires from the battery housing by pulling 

on each wire until it releases from the battery 

housing.  Insert the 1xLi-ion battery pack or 4 

x AAA battery and noting the correct polarity. 

Close the battery box. Please dispose and 

recycle the packaging and “TEST IT” button with 

the wires according to the local regulations.

7297, 

LED LENSER® H7.2 (gift box)

7397, 

LED LENSER® H7.2 (Blister with “TEST IT” 

function)

Version of the operating manual: V 1.3

4 x AAA / LR03 (1.5 V DC)

There are two switches on the H7.2. The front 

switch is located in the upper part of the 

headlamp housing. This button is used to turn 

the H7.2 ON/OFF. It is also used to activate the 

various Light Programs, Lighting Functions (see 

Section 5.1) and to active the “transport lock” 

function (see Section 6).

The Multi-function “Wheel” switch is located 

on the backside in the upper part of the battery 

box. This allows you to adjust the brightness 

and flash rate infinitely and to change the light 

modes (see Section 5.1).

In the front, narrower region of the headlamp 

housing is the reflector lens through which 

the light of the LED is focusable. The reflector 

lens is held by a plastic ring. You can rotate 

that plastic ring using two fingers, and thus 

adjust the focus quickly and easily. This is our 

patented Speed Focus system, which allows the 

adjustment of the light beam’s focus.

You also can adjust the hinge of the headlamp, 

depending on whether you want to illuminate 

an area in the distance or in front of you. For 

this, you simply tilt the part of the head lamp 

containing the reflector lens and the LED. 

Smart Light Technology (SLT) is a program that 

consists of computer optimized microcontrollers 

which allows our products to have various 

lighting functions. The H7.2 is equipped with 

this technology and is therefore able to use 

various Light Programs and Functions (see 

Section 5) with an interface that is simple and 

user friendly. By pressing the front switch on 

the lamp head you can activate the following 

light functions: On (Power) – Off, Low Power, 

Boost and Signal. With the Multi-function “Wheel” 

switch on the back, the light intensity (down 

to 5 lm) and flashing rate (1–24Hz) is infinitely 

adjustable by easily rotating the switch. By 

pressing the “Multi-function Wheel” switch you 

can change the light mode. 

The H7.2 is equipped with one LED (Light 

Emitting Diode). The LED is very strong and 

ideal for normal use. For example if the Turning 

Focus or the adjustment of the angle of light 

beam to the horizontal should be used. 

The boost mode of H7.2 can be turned on when 

the flashlight is off and then pushing the front 

switch for approx. 5 seconds. Release the switch 

when the boosted light is on, otherwise the 

product will enter “transport lock” (see Section 

6).

In H7.2, there are three different modes (Easy 

Low, Easy Power, Signal). The default mode is 

the Easy Low mode. 

When the product is off, press the “Multi-function 

Wheel” switch on the back for 5 second. It will 

achieve transition mode. Then the LED will blink 

once to indicate that it is mode one; then blink 

twice for mode two; and finally blink thrice for 

mode three.

a) Light Mode one - Easy Low: when the product 

is off, firmly press the front button until it blinks 

once. The LED will glow at its lowest brightness 

(light function: dim light). Two times touch to 

the button on top of the lamp within 1 second 

will turn on the lamp to its full brightness (light 

function: strong light), and third touch will turn 

the lamp off.

b) Light Mode two - Easy Power: when the 

product is off, firmly press the front button until 

it blinks twice. The LED will glow at its fullest 

brightness (light function: strong light). Two 

times touch to the button on top of the lamp 

within 1 second will turn on the lamp to its 

lowest brightness (light function: dim), and third 

touch will turn the lamp off.

c) Light Mode three - Signal: when the product 

is off, firmly press the front button until it blinks 

thrice. The LED will glows with full brightness 

(light function: strong light). Two times touch to 

the button on top of the lamp within 1 second 

will start the strobe (12 Hz), and a third touch 

will turn the lamp off. The speed at which the 

strobe will blink can be adjusted by turning the 

knob on the battery box. 

When the flashlight is on, rotate the “Multi-

function Wheel” switch on the back to adjust the