Справочник Пользователя для Albrecht BPA 300 15510
Модели
15510
•
After switching on, the device remains in Standby mode and flashes every 3
sec.
sec.
Turning off the adapter:
•
Press and hold the button for approximately 3 sec. again, LED will flash 3 x red
•
The complete headset will be turned off and the LED indicator will stop flashing.
Pairing the wireless adapter + headset with a Phone, Navigator or other Adapter
The wireless adapter with the headset must be paired with the other Bluetooth device before
it can be used for the first time. This one-time pairing process is necessary, otherwise the
Bluetooth devices do not know that they have to fit to each other. During pairing, the 2 devices
exchange and store their data and later can be reconnected any time just by switching them
on, without any need to complete the pairing process once more again. The headset adapter
can store pairing information for up to 7 different Bluetooth (or compatible) devices.
The wireless adapter with the headset must be paired with the other Bluetooth device before
it can be used for the first time. This one-time pairing process is necessary, otherwise the
Bluetooth devices do not know that they have to fit to each other. During pairing, the 2 devices
exchange and store their data and later can be reconnected any time just by switching them
on, without any need to complete the pairing process once more again. The headset adapter
can store pairing information for up to 7 different Bluetooth (or compatible) devices.
Initiating the pairing process
Please place the headset close to the other device you wish to pair with.
Please place the headset close to the other device you wish to pair with.
•
Make sure the headset is turned off (the LED indicator shall be off and not flashing).
•
Hold the Talk Button for longer than approximately 6 seconds until the LED indicator
begins to flash red and green. (After the first 3 seconds the LED will first flash 3 x
green because it switches on).
begins to flash red and green. (After the first 3 seconds the LED will first flash 3 x
green because it switches on).
Note: Do not release the button at the point, where the 3 x blue flashes happen, this is too
early!.
early!.
The headset is now ready to be paired with the Bluetooth mobile phone, radio, radio adapter or
navigator. You will have about 1 minute time now to prepare the other Bluetooth device for the
pairing process.
navigator. You will have about 1 minute time now to prepare the other Bluetooth device for the
pairing process.
•
Operate the mobile phone or navigator and go through the steps of searching for
nearby Bluetooth devices. Please refer to the operating guide of the Bluetooth mobile
phone to perform Bluetooth pairing procedure.
nearby Bluetooth devices. Please refer to the operating guide of the Bluetooth mobile
phone to perform Bluetooth pairing procedure.
•
When the Bluetooth mobile phone or navigator has detected the headset, the LCD
screen on the mobile phone will display BPA-300.
screen on the mobile phone will display BPA-300.
•
Follow the instructions on the Bluetooth mobile phone to complete the headset pairing.
When the mobile phone prompts for a pin code or password enter 0000.
When the mobile phone prompts for a pin code or password enter 0000.
If pairing is not completed within 60 seconds, the red-green flashing will stop and in that case,
you can repeat the steps described above. The screen on the Bluetooth mobile phone or
navigator will display the pairing status. When pairing is successful, the screen on the
Bluetooth mobile phone will display a pairing successful message (or similar) and the LED
indicator on the headset adapter will show
you can repeat the steps described above. The screen on the Bluetooth mobile phone or
navigator will display the pairing status. When pairing is successful, the screen on the
Bluetooth mobile phone will display a pairing successful message (or similar) and the LED
indicator on the headset adapter will show
•
Standby
or
•
Connected ready for talk (green 2 x flashing every 3 seconds)
,
depending on the connection status requested from the other device side).
Now the headset is successfully paired and ready to make and receive calls or
announcements.
announcements.