Справочник Пользователя для Rc Logger GPS sensor module 20001RC

Модели

20001RC

GPS module

No. 20001RC

Version 03/11

iNteNded uSe

This product is intended for working with the RC Logger (not included) to provide GPS information for a model vehicle.

The product is powered by the RC Logger.

For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product

for purposes other than those described above, the product may be damaged. In addition, improper use can

cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.

Make this product available to third parties only together with its operating instructions.

deliveRy CoNteNt

GPS module

Logger connection cable (20 cm)

Module connection cable (20 cm)

Operating instructions

Safety iNStRuCtioNS

Read the operating instructions carefully and especially observe the safety information. if

you do not follow the safety instructions and information on proper handling in this manual,

we assume no liability for any resulting personal injury or damage to property. Such cases

will invalidate the warranty/guarantee.

Persons / Product

The device is not a toy. Keep it out of the reach of children and pets.

Do not leave packaging material lying around carelessly. These may become dangerous playing material

for children.

Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,

flammable gases, vapours and solvents.

Do not place the product under any mechanical stress.

If it is no longer possible to operate the product safely, take it out of operation and protect it from any

accidental use. Safe operation can no longer be guaranteed if the product:

is visibly damaged,

is no longer working properly,

has been stored for extended periods in poor ambient conditions or

has been subjected to any serious transport-related stresses.

Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

Also observe the safety and operating instructions of any other devices which are connected to the

product.

Miscellaneous

Consult an expert when in doubt about operation, safety or connection of the device.

Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified

shop.

If you have questions which remain unanswered by these operating instructions, contact our technical

support service or other technical personnel.

oPeRatioN

the GPS module may not work with strong electromagnetic interference. Stay away from

sources of electromagnetic interference and restart the GPS module if you have had

problems with it.

Attach the GPS module on the vehicle body firmly with cable ties, glue or double sided adhesive tape.

When installing the module, you should also take care that the cables connected to the module

are not kinked nor pinched.

The side with LED should face outward and expose to the sky. The side with the sockets should

not face upward. Misplace of the module may result in a reduced ability to receive of GPS

information.

Connect the GPS module to the RC Logger with the logger connection cable provided via either socket at

the bottom of the GPS module.

If you would like to install an additional module to the system, connect it to the GPS module via the other

socket.

Power on the RC Logger. The red LED on the GPS module lights up for about 3 seconds indicating the

module is turned on.

Then, the green LED on the GPS module lights up for about 4 seconds. This indicates the GPS module is

operating and is trying to get satellite information.

The time for getting the GPS information depends on the environment. GPS module normally takes a few

minutes to get the information. If the environment is good, it may take around one minute to receive the

location information. Before recording, you need to wait until the green LED blinks and two short beeps are

emitted, which indicates the location information is available.

You will hear a long beep if the location information is not available. The green LED is keep glowing and

the module is trying to get the GPS signal. If the location information is ready again, the green LED blinks

and two short beeps are emitted.

Record video or takes photo with the RC Logger when the green LED on the GPS module is blinking. GPS

information is recorded to the RC Logger at the same time.

Please refer to the instructions of the RC Logger for data retrieval.

diSPoSal

In order to preserve, protect and improve the quality of environment, protect human health and

utilise natural resources prudently and rationally, the user should return unserviceable product to

relevant facilities in accordance with statutory regulations.

The crossed-out wheeled bin indicates the product needs to be disposed separately and not as

municipal waste.

teChNiCal data

Operating voltage:

3.6 – 6 V

Maximum current consumption:

100 mA

GPS sampling rate:

5 Hz

Operation temperature:

-20 to +60 ºC

Storage temperature:

-30 to +60 ºC

Internal buzzer sound pressure level:

min. 70 dB

Output data:

Date

Time

Latitude

Longitude

Altitude

Speed over ground

Course over ground

Number of Satellites

Positional Dilution of Precision (PDOP)

Vertical Dilution of Precision (VDOP)

Dimensions (W x H x D):

30 x 43 x 16 mm

Weight:

22 g

These operating instructions are published by CEI Conrad Electronic International (HK) Limited,

28th Floor & 2903-9, Pacific Plaza, 418 Des Voeux Road West, Hong Kong.

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the

capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also

in part, is prohibited.

The operating instructions reflect the current technical specifications at time of print. We reserve the right to

V1_0311-HL