Справочник Пользователя для Jabra GN9120 Midi 9120-4801



5

determine the type of interface. 

 Note: If more than 15 seconds elapses without pressing the volume + or volume – buttons, the last 

selected interface will be activated.

5. To exit the interface switching mode, press the volume + and volume – buttons simultaneously for 6 

seconds.

6. Only with the GN1000: Complete the setting up procedure according to its Quick Guide.

4. Audio and visual indicators

The  GN9120/GN9125’s  headset  and  base  have  audio  and  visual  indicators,  which  represent  various 
actions and aspects associated with setting up and operating the product. The headset gives audio and 
visual  indications.  The  base  gives  various  visual  indications  via  its  online,  link  and  general  indicators. 
Familiarize yourself with these indicators to fully benefit from your GN9120/GN9125.

Out of range  

Beep every 10 sec.

Mute ON  

Beep every 15 sec.

Low Battery Charge  

Beep every 20 sec.

Adjusting Volume  

Low single tone per press

Maximum Volume reached 

Short beep

Minimum Volume reached 

Short beep

Tone control adjustment  

Beep (indicating 6 sec. has passed)

Adding a headset at conference call 

Beep in master headset

Incoming call  

Beep (only if using GN1000)

Low Power mode  

Flashes rapidly when switching 

 

 

between modes

Transmit volume adjustment  

Flashes rapidly when switching 

 

 

between modes

Charging in Process  

Battery charging indicator flashes

Charging completed  

Battery charging indicator ON

Mute 

Mute indicator ON

Low Power Mode  

Link-up indicator flashes every 10 sec.

Adding a headset to conference call 

All lights are flashing, followed by battery indicator ON 

Link between headset and base 

Link-up indicator ON

EHS (Electronic Hook Switch) setting 

Please refer to separate section

Pairing of Headset and Base 

All lights are flashing for approx. 

 

 

 sec., followed by battery indicator 
ON

On a call 

On-line indictor flashes

3. Remote handset lifting functionality

Answering and making telephone calls with GN1000
You may purchase a GN1000 as an accessory, which lets you answer 
and end telephone calls while away from your desk. Please contact 
your vendor or visit www.jabra.com for further information.

To answer a call using the GN1000 or electronic hook switch
functionality:
1. Remove the headset from the base unit when you receive a call. 

The link will be established and the on-line indicator on the front 
of the base unit will begin to flash.

:

  If  you  are  already  wearing  the  headset,  simply  press  the  multifunction  button  on  the  headset 

momentarily to answer the incoming call.

To end the call, press the multifunction button momentarily or place the headset in the base unit.

Making telephone calls using the GN1000 or electronic hook switch functionality:
To make a telephone call using the GN1000:
1. Remove the headset from the base unit. The link will be established and the on-line indicator on the 

front of the base unit will begin to flash.

2. Dial the desired number. To end the call, press the multifunction button momentarily or place the head-

set in the base unit.

Note: The connection cord must be connected to your telephone’s handset port (not the headset port) 
in order for the GN1000 to function.

GN9120/GN9125 with Electronic Hook Switch (EHS)
The GN9120/GN9125 comes in versions which enables you to answer and end calls while away from your 
desk – without using the GN1000. This is, however, only possible on certain telephone systems.

In order to determine which telephones have the EHS feature enabled, please refer to our website 
www.jabra.com. Please also refer to your telephone’s user manual for clarification.

3 modes are available:
•  The RHL interface (non-EHS; works with the GN1000)
•  The DHSG interface (for example, with Siemens and Elmeg desk telephones)
•  The AEI interface (for example, with Tenovis desk telephones)
Note: By default, the EHS-version of the GN9120/GN9125 is set to the DHSG interface.
 

 

To toggle between DHSG, AEI and RHL interface, complete the following:
1. Place the headset in the base with its on-line indicator facing you.
2. Press the volume + and volume – buttons on the 

headset  simultaneously  for  6  seconds  while  the 
headset is in the base, until the headset’s on-line 
indicator flashes rapidly.

3. You are now in interface switching mode, and can 

set  the  GN9120/GN9125  to  work  with  your  tel-
ephone’s interface.

. Using the volume + button to move right and the 

volume – button to move left, select the required 
EHS interface. 

  The base unit’s 3 indicators show which interface 

the GN9120/GN9125 is in. See the illustration to 

RHL

DSHG

AEI

Link icon

Mute icon

Charge icon

Volume button

–

+