Справочник Пользователя для Freescale Semiconductor Demonstration Board for Freescale MC9S12XHY256 Microcontroller DEMO9S12XHY256 DEMO9S12XHY256
Модели
DEMO9S12XHY256
S12X Debug (S12XDBGV3) Module
MC9S12XHY-Family Reference Manual, Rev. 1.04
230
Freescale Semiconductor
6.3.2.1
Debug Control Register 1 (DBGC1)
Read: Anytime
Write: Bits 7, 1, 0 anytime
Bit 6 can be written anytime but always reads back as 0.
Bits 5:2 anytime S12XDBG is not armed.
Bits 5:2 anytime S12XDBG is not armed.
If a write access to DBGC1 with the ARM bit position set occurs
simultaneously to a hardware disarm from an internal trigger event, then the
ARM bit is cleared due to the hardware disarm.
simultaneously to a hardware disarm from an internal trigger event, then the
ARM bit is cleared due to the hardware disarm.
NOTE
When disarming the S12XDBG by clearing ARM with software, the
contents of bits[5:2] are not affected by the write, since up until the write
operation, ARM = 1 preventing these bits from being written. These bits
must be cleared using a second write if required.
contents of bits[5:2] are not affected by the write, since up until the write
operation, ARM = 1 preventing these bits from being written. These bits
must be cleared using a second write if required.
Address: 0x0020
7
6
5
4
3
2
1
0
R
ARM
0
reserved
BDM
DBGBRK
reserved
COMRV
W
TRIG
Reset
0
0
0
0
0
0
0
0
Figure 6-3. Debug Control Register (DBGC1)
Table 6-4. DBGC1 Field Descriptions
Field
Description
7
ARM
Arm Bit — The ARM bit controls whether the S12XDBG module is armed. This bit can be set and cleared by
user software and is automatically cleared on completion of a tracing session, or if a breakpoint is generated with
tracing not enabled. On setting this bit the state sequencer enters State1.
0 Debugger disarmed
1 Debugger armed
user software and is automatically cleared on completion of a tracing session, or if a breakpoint is generated with
tracing not enabled. On setting this bit the state sequencer enters State1.
0 Debugger disarmed
1 Debugger armed
6
TRIG
Immediate Trigger Request Bit — This bit when written to 1 requests an immediate trigger independent of
comparator signal status. When tracing is complete a forced breakpoint may be generated depending upon
DBGBRK and BDM bit settings. This bit always reads back a 0. Writing a 0 to this bit has no effect. If TSOURCE
is clear no tracing is carried out. If tracing has already commenced using BEGIN- or MID trigger alignment, it
continues until the end of the tracing session as defined by the TALIGN bit settings, thus TRIG has no affect. In
secure mode tracing is disabled and writing to this bit has no effect.
0 Do not trigger until the state sequencer enters the Final State.
1 Trigger immediately .
comparator signal status. When tracing is complete a forced breakpoint may be generated depending upon
DBGBRK and BDM bit settings. This bit always reads back a 0. Writing a 0 to this bit has no effect. If TSOURCE
is clear no tracing is carried out. If tracing has already commenced using BEGIN- or MID trigger alignment, it
continues until the end of the tracing session as defined by the TALIGN bit settings, thus TRIG has no affect. In
secure mode tracing is disabled and writing to this bit has no effect.
0 Do not trigger until the state sequencer enters the Final State.
1 Trigger immediately .
5
reserved
This bit is reserved, setting it has no meaning or effect.
4
BDM
Background Debug Mode Enable — This bit determines if an S12X breakpoint causes the system to enter
Background Debug Mode (BDM) or initiate a Software Interrupt (SWI). If this bit is set but the BDM is not enabled
by the ENBDM bit in the BDM module, then breakpoints default to SWI.
0 Breakpoint to Software Interrupt if BDM inactive. Otherwise no breakpoint.
1 Breakpoint to BDM, if BDM enabled. Otherwise breakpoint to SWI
Background Debug Mode (BDM) or initiate a Software Interrupt (SWI). If this bit is set but the BDM is not enabled
by the ENBDM bit in the BDM module, then breakpoints default to SWI.
0 Breakpoint to Software Interrupt if BDM inactive. Otherwise no breakpoint.
1 Breakpoint to BDM, if BDM enabled. Otherwise breakpoint to SWI