Техническая Спецификация для Atmel ATmega328P Xplained Mini MEGA328P-XMINI MEGA328P-XMINI
Модели
MEGA328P-XMINI
160
ATmega48A/PA/88A/PA/168A/PA/328/P [DATASHEET]
Atmel-8271H-AVR- ATmega-Datasheet_08/2014
EXCLK should be done before asynchronous operation is selected. Note that the crystal Oscillator will only run
when this bit is zero.
when this bit is zero.
• Bit 5 – AS2: Asynchronous Timer/Counter2
When AS2 is written to zero, Timer/Counter2 is clocked from the I/O clock, clk
I/O
. When AS2 is written to one,
Timer/Counter2 is clocked from a crystal Oscillator connected to the Timer Oscillator 1 (TOSC1) pin. When the
value of AS2 is changed, the contents of TCNT2, OCR2A, OCR2B, TCCR2A and TCCR2B might be corrupted.
value of AS2 is changed, the contents of TCNT2, OCR2A, OCR2B, TCCR2A and TCCR2B might be corrupted.
• Bit 4 – TCN2UB: Timer/Counter2 Update Busy
When Timer/Counter2 operates asynchronously and TCNT2 is written, this bit becomes set. When TCNT2 has
been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that TCNT2 is ready to be updated with a new value.
been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that TCNT2 is ready to be updated with a new value.
• Bit 3 – OCR2AUB: Output Compare Register2 Update Busy
When Timer/Counter2 operates asynchronously and OCR2A is written, this bit becomes set. When OCR2A has
been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that OCR2A is ready to be updated with a new value.
been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that OCR2A is ready to be updated with a new value.
• Bit 2 – OCR2BUB: Output Compare Register2 Update Busy
When Timer/Counter2 operates asynchronously and OCR2B is written, this bit becomes set. When OCR2B has
been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that OCR2B is ready to be updated with a new value.
been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that OCR2B is ready to be updated with a new value.
• Bit 1 – TCR2AUB: Timer/Counter Control Register2 Update Busy
When Timer/Counter2 operates asynchronously and TCCR2A is written, this bit becomes set. When TCCR2A
has been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that TCCR2A is ready to be updated with a new value.
has been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that TCCR2A is ready to be updated with a new value.
• Bit 0 – TCR2BUB: Timer/Counter Control Register2 Update Busy
When Timer/Counter2 operates asynchronously and TCCR2B is written, this bit becomes set. When TCCR2B
has been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that TCCR2B is ready to be updated with a new value.
has been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit
indicates that TCCR2B is ready to be updated with a new value.
If a write is performed to any of the five Timer/Counter2 Registers while its update busy flag is set, the updated
value might get corrupted and cause an unintentional interrupt to occur.
value might get corrupted and cause an unintentional interrupt to occur.
The mechanisms for reading TCNT2, OCR2A, OCR2B, TCCR2A and TCCR2B are different. When reading
TCNT2, the actual timer value is read. When reading OCR2A, OCR2B, TCCR2A and TCCR2B the value in the
temporary storage register is read.
TCNT2, the actual timer value is read. When reading OCR2A, OCR2B, TCCR2A and TCCR2B the value in the
temporary storage register is read.
18.11.9 GTCCR – General Timer/Counter Control Register
• Bit 1 – PSRASY: Prescaler Reset Timer/Counter2
When this bit is one, the Timer/Counter2 prescaler will be reset. This bit is normally cleared immediately by
hardware. If the bit is written when Timer/Counter2 is operating in asynchronous mode, the bit will remain one
until the prescaler has been reset. The bit will not be cleared by hardware if the TSM bit is set. Refer to the
description of the
hardware. If the bit is written when Timer/Counter2 is operating in asynchronous mode, the bit will remain one
until the prescaler has been reset. The bit will not be cleared by hardware if the TSM bit is set. Refer to the
description of the
Timer/Counter Synchronization mode.
Bit
7
6
5
4
3
2
1
0
TSM
–
–
–
–
–
PSRASY
PSRSYNC
GTCCR
Read/Write
R/W
R
R
R
R
R
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0