Техническая Спецификация для Lappkabel 1027760 ÖLFLEX CHAIN 808 CP 3G0,75 Grey 1027760
Модели
1027760
U.I. Lapp
GmbH
DATA SHEET
ÖLFLEX
®
CHAIN 808 CP
DB 1027751
valid from: 26.01.2012
Originator: HESC1 / PDC
approved: HAPF1 / PDC
Document:
DB00127751EN
Page 1 of 1
All rights reserved acc. to DIN ISO 16016.
PD 0019/2.2_11.10EN
Application
ÖLFLEX
CHAIN 808 CP cables are high-flexible oil-resistant power and control cables with an outer sheath of Polyurethane
for flexible use and fixed installation under light or medium mechanical load conditions. They are among others designed for
use in dry, damp or wet rooms. Considering the indicated temperature range an outdoor use is possible. ÖLFLEX
use in dry, damp or wet rooms. Considering the indicated temperature range an outdoor use is possible. ÖLFLEX
CHAIN
808 CP cables are increased oil resistant and at room temperature widely resistant to acids and caustic solutions. The outer
sheath is resistant to high mechanical load, particularly to abrasion and scouring, cut resistant, microbe-proof and hydrolysis
resistant. They are especially suitable for basic requirements (Basic Line)
sheath is resistant to high mechanical load, particularly to abrasion and scouring, cut resistant, microbe-proof and hydrolysis
resistant. They are especially suitable for basic requirements (Basic Line)
in power chains and in permanently moved ma-
chine parts. Usage of these cables in moving cable carriers or on motor drum guidance or under a tensile strain of more
than 15 N/mm
than 15 N/mm
2
conductor cross-section is not allowed. The screen is a protection against electrical interference.
Application range:
Power chains or moving machine parts, especially in wet areas of machine tools and transfer lines, measuring, control
and regulation circuits.
Power chains or moving machine parts, especially in wet areas of machine tools and transfer lines, measuring, control
and regulation circuits.
Design
Design
based on HD 22.10 S2 resp. VDE 0282-10 and HD 21.13 S1 +A1 resp. VDE 0281-13
Conductor
fine wire strands of bare copper acc. to IEC 60228 resp. VDE 0295, Class 5
Core insulation
LAPP special PVC compound P8/1, better than the PVC compound TI2
acc. to HD 21.1 S4 resp. VDE 0281-1
Core identification
acc. to VDE 0293-1, with or without GN/YE protective conductor
black cores with white numbers
acc. to DIN EN 50334 resp. VDE 0293 part 334
Taping
non-woven wrapping
Screen
braid of tinned copper wires, coverage = 85% (nominal value)
Outer sheath
Polyurethane compound TMPU acc. to EN 50363-10-2 resp. VDE 0207-363-10-2
Colour: Grey, similar RAL 7001
Electrical properties
Nominal voltage
U
0
/U:
300/500 V
Test voltage
Core/Core: 4000 V AC
Core/Screen: 2000 V AC
Mechanical and thermal properties
Min. bending radius
flexing up to 3m travel distance (horizontal, self supporting): 10 x cable diameter
flexing up to 10m travel distance (horizontal, sliding): 12 x cable diameter
fixed installation:
4 x cable diameter
Temperature range
flexing:
-5 °C up to +70 °C max. conductor temp.
fixed installation:
-40 °C up to +80 °C max. conductor temp.
Travel distance
for travel distances up to 10m (horizontal):1…2 Mio bending change cycles
Please comply with the assembly guidelines Appendix T3
Oil resistance
acc. to EN 50363-10-2 resp. VDE 0207-363-10-2
Tests
acc. to IEC 60811 resp. VDE 0473 part 811, EN 50395, EN 50396
EC Directives
This cable is conform to the EC-Directives 2006/95/EC (Low Voltage Directive)
and 2002/95/EC (RoHS, Restriction of the use of certain hazardous substances).