Техническая Спецификация для ZyXEL VMG1312-B10A VMG1312-B10A-EU01V1F
Модели
VMG1312-B10A-EU01V1F
Chapter 10 Quality of Service (QoS)
VMG1312-B10A User’s Guide
178
Service
This field is available only when you select IP in the Ether Type field.
This field simplifies classifier configuration by allowing you to select a predefined
application. When you select a predefined application, you do not configure the rest of the
filter fields.
application. When you select a predefined application, you do not configure the rest of the
filter fields.
IP Protocol
This field is available only when you select IP in the Ether Type field.
Select this option and select the protocol (service type) from TCP, UDP, ICMP or IGMP. If
you select User defined, enter the protocol (service type) number.
you select User defined, enter the protocol (service type) number.
DHCP
This field is available only when you select IP in the Ether Type field.
Select this option and select a DHCP option.
If you select Vendor Class ID (DHCP Option 60), enter the Vendor Class Identifier
(Option 60) of the matched traffic, such as the type of the hardware or firmware.
(Option 60) of the matched traffic, such as the type of the hardware or firmware.
If you select User Class ID (DHCP Option 77), enter a string that identifies the user’s
category or application type in the matched DHCP packets.
category or application type in the matched DHCP packets.
Packet
Length
This field is available only when you select IP in the Ether Type field.
Select this option and enter the minimum and maximum packet length (from 46 to 1500) in
the fields provided.
the fields provided.
DSCP
This field is available only when you select IP in the Ether Type field.
Select this option and specify a DSCP (DiffServ Code Point) number between 0 and 63 in the
field provided.
field provided.
802.1P
This field is available only when you select 802.1Q in the Ether Type field.
Select this option and select a priority level (between 0 and 7) from the drop-down list box.
"0" is the lowest priority level and "7" is the highest.
VLAN ID
This field is available only when you select 802.1Q in the Ether Type field.
Select this option and specify a VLAN ID number.
TCP ACK
This field is available only when you select IP in the Ether Type field.
If you select this option, the matched TCP packets must contain the ACK (Acknowledge)
flag.
flag.
Exclude
Select this option to exclude the packets that match the specified criteria from this classifier.
DSCP Mark
This field is available only when you select IP in the Ether Type field.
If you select Mark, enter a DSCP value with which the Device replaces the DSCP field in the
packets.
packets.
If you select Unchange, the Device keep the DSCP field in the packets.
802.1P Mark
Select a priority level with which the Device replaces the IEEE 802.1p priority field in the
packets.
packets.
If you select Unchange, the Device keep the 802.1p priority field in the packets.
VLAN ID
If you select Remark, enter a VLAN ID number with which the Device replaces the VLAN ID
of the frames.
of the frames.
If you select Remove, the Device deletes the VLAN ID of the frames before forwarding
them out.
them out.
If you select Add, the Device treat all matched traffic untagged and add a second VLAN ID.
If you select Unchange, the Device keep the VLAN ID in the packets.
Forward to
Interface
Interface
Select a WAN interface through which traffic of this class will be forwarded out. If you select
Unchange, the Device forward traffic of this class according to the default routing table.
Unchange, the Device forward traffic of this class according to the default routing table.
Table 45
Class Setup: Add/Edit (continued)
LABEL
DESCRIPTION