Техническая Спецификация для MEAN WELL CLG-60-12

12V

15V

20V

24V

27V

36V

48V

0 ~ 5A

0 ~ 4A

0 ~ 3A

0 ~ 2.5A

0 ~ 2.3A

0 ~ 1.7A

0 ~ 1.3A

60W

60W

60W

60W

62.1W

61.2W

62.4W

2Vp-p

2.4Vp-p

1.8Vp-p

2.7Vp-p

2.7Vp-p

3.6Vp-p

4.6Vp-p

±10%

Fixed can be modified between the range above

Fixed. Can be modified between 3% ~ -25% rated output current

±3.0%

±5.0%

500ms / 230VAC    3000ms / 115VAC at full load

90 ~ 295VAC          127 ~ 417VDC

47 ~ 63Hz

PF>0.94/115VAC, PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

85%

86%

87.5%

87%

88%

89%

89%

13.8 ~ 16V

17.5 ~ 21V

23 ~ 28V

28 ~ 32V

31 ~ 35V

41 ~ 46V

54 ~ 60V

COLD START 35A(twidth=45 s measured at 50% Ipeak) at 230VAC

μ

<0.75mA / 240VAC

95 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Hiccup mode, recovers automatically after fault condition is removed

-30 ~ +70

 

℃ (Refer to "Derating Curve")

20 ~ 95% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

℃

±

℃

℃

0.03%/

 (0 ~ 50

)

10 ~ 500Hz, 5G 12min./1cycle, period for  72min. each along X, Y, Z axes

495.7Khrs min.      MIL-HDBK-217F (25

)

℃

195.6*61.5*38.8mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristics for more details.

5. Please refer to "DRIVING METHODS OF LED MODULE".

6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the 

    complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.

8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently 

      connected to the mains.

0.86Kg; 16pcs/14.8Kg/0.54CUFT

Protection type : Shut down o/p voltage, re-power on to recover

60W Single Output LED Power Supply

‧

Universal AC input / Full range (up to 295VAC)

‧

Built-in active PFC function

‧

‧

Protections: Short circuit / Over current / Over voltage / Over temperature 

‧

Cooling by free air convection

‧

IP67 design for indoor or outdoor installations

‧

Class 2 power unit

‧

Pass LPS

‧

100% full load burn-in test

‧

High reliability

‧

Suitable for LED lighting and moving sign applications 

(Note.2)

‧

Compliance to worldwide safety regulations for lighting 

‧

Suitable for dry / damp / wet locations

‧

3 years warranty

High efficiency up to 89%

■

 Features :

Shut down o/p voltage, recovers automatically after temperature goes down

I/P-O/P:3.75KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC

I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH

Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (≧75% load) ; EN61000-3-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level (surge 4KV),  criteria A

10.5 ~ 15V

14 ~ 20V

16.8 ~ 24V

18.9 ~ 27V

25.2 ~ 36V

33.6 ~ 48V

8.4 ~ 12V

5A

4A

3A

2.5A

2.3A

1.7A

1.3A

11.5 ~ 13V

14.5 ~ 16.2V

19.5 ~ 22V

24 ~ 26V

25 ~ 30V

32.5 ~ 39V

43.6 ~ 51.8V

IP67

..

( for 48V only)

( except for 48V )

0.8A/115VAC          0.4A/230VAC          0.3A/277VAC

UL879, UL8750, UL1310, TUV EN61347-1, EN61347-2-13 independent, CAN/CSA C22.2 No. 223-M91(except for 48V),

CSA C22.2 No. 250.0-08(except for 48V), CSA C22.2 No. 207-M89(except for 48V), IP67, J61347-1, J61347-2-13 approved