Техническая Спецификация для Otto Pushbutton 28 Vdc 5 A 1 x On/(On) IP68 momentary 1 pc(s) P9-413121W
Модели
P9-413121W
SEALED DOME PUSHBUTTON SWITCHES
DOME
PUSHBUTTONS
P9
Specifications Subject To Change Without Notice
www.ottoexcellence.com 93
P
U
S
H
B
U
T
T
O
N
S
CHOICE OF SNAP-ACTION & SHORTING BAR ACTION
ORDERING INFORMATION:
Select the OTTO P9 series features that
match your specific application. Standard
and special features are shown at right.
Specify your choice by building the OTTO
Part Number code.
match your specific application. Standard
and special features are shown at right.
Specify your choice by building the OTTO
Part Number code.
Example: P9-211121 specifies raised
dome style button, threaded case, solder
terminals, N.O. circuit form, standard
snap-action, black case/bezel, red button.
dome style button, threaded case, solder
terminals, N.O. circuit form, standard
snap-action, black case/bezel, red button.
0.110” Quick Connect Detail
15/32-32 UNRS-2A
THD to within 0.062
of shoulder
THD to within 0.062
of shoulder
(As viewed from switch bottom.)
Button & Case Style***
Terminal Style Circuit
Form
Switch Action
Case/
Bezel Color
Bezel Color
Button
Color
Color
1. Flush Dome & Threaded Case, Std. Finish
2. Raised Dome & Threaded Case, Std. Finish
3. Flush Dome & Snap-In Case, Std. Finish
4. Raised Dome & Snap-In Case, Std. Finish
5. Flush Dome & Threaded Case, Matte Finish
6. Raised Dome & Threaded Case, Matte Finish
7. Flush Dome & Snap-In Case, Matte Finish
8. Raised Dome & Snap-In Case, Matte Finish
2. Raised Dome & Threaded Case, Std. Finish
3. Flush Dome & Snap-In Case, Std. Finish
4. Raised Dome & Snap-In Case, Std. Finish
5. Flush Dome & Threaded Case, Matte Finish
6. Raised Dome & Threaded Case, Matte Finish
7. Flush Dome & Snap-In Case, Matte Finish
8. Raised Dome & Snap-In Case, Matte Finish
1. Solder
2. PC Pin
3. 0.110”
2. PC Pin
3. 0.110”
Quick Connect
1. N.O.
2. N.C. ➀
3. 2 Circuit ➀
2. N.C. ➀
3. 2 Circuit ➀
1. Standard Snap-Action
2. Low Force Snap-Action
3. Non-Snap Shorting Bar
2. Low Force Snap-Action
3. Non-Snap Shorting Bar
1. Red
2. Black
3. Orange**
4. Yellow**
5. Green**
6. Blue**
7. Purple**
8. Gray**
9. White
2. Black
3. Orange**
4. Yellow**
5. Green**
6. Blue**
7. Purple**
8. Gray**
9. White
1. Red
2. Black
3. Orange
4. Yellow
5. Green
6. Blue
7. Purple
8. Gray
9. White
2. Black
3. Orange
4. Yellow
5. Green
6. Blue
7. Purple
8. Gray
9. White
P9 PART NUMBER CODE
P9 –
X X X X X X *
➀
Not available in Shorting Bar version.
* Add “W” suffix for watertight to IP68S.
** Contact factory for minimum requirement.
*** Contact factory for std./matte button/case combination options.
** Contact factory for minimum requirement.
*** Contact factory for std./matte button/case combination options.
•
Snap-in case allows front panel mounting into 0.024” or 0.118”
thick panels using panel gasket 401669 or into 0.031” and
0.125” thick panels
thick panels using panel gasket 401669 or into 0.031” and
0.125” thick panels
•
0.110" Quick Connect terminals allow reliable, solderless
wire connections
wire connections
•
Flush Neoprene Boot P/N 402339
•
Raised Neoprene Boot P/N 402246
* Must use panel gasket 401669 supplied with the switch.
Recommended Panel Openings
*Panel Thickness
Recommended 0
DIM. Across D-Flat
0.024*
0.505
0.460
0.031
0.505
0.460
0.118*
0.505
0.460
0.125
0.505
0.460
15/32-32 UNRS-2A
THD to within 0.062
of shoulder
THD to within 0.062
of shoulder
Raised Dome Button Style
Snap-In Case
(PC Terminals Shown)
Flush Dome Button Style
Solder Terminals
(Terminals not
orientated to flat)
PC Pin
(Orientated to case
flats as shown)