Справочник Пользователя для Jeti RC console 2.4 GHz No. of channels: 16 80001571
Модели
80001571
computer radio control system
EN
defined (completely off) throttle position once the assigned switch
is activated.
is activated.
5.
Throttle Idle Setting
This feature is used to set the idle position for your throttle and will
prevent your engine from shutting-off when you moving throttle
stick to its low position. The minimum throttle setting is defined by
editing the “Idle Offset” value. When this function has been
activated, the minimum throttle setting (idle point) is defined by the
offset value as a percentage. Standard throttle function is not
affected by the idle offset setting.
prevent your engine from shutting-off when you moving throttle
stick to its low position. The minimum throttle setting is defined by
editing the “Idle Offset” value. When this function has been
activated, the minimum throttle setting (idle point) is defined by the
offset value as a percentage. Standard throttle function is not
affected by the idle offset setting.
4.
4.
9.3.2 Sticks / Switches Setup
This menu contains System Stick/Switch settings and configuration.
Various functions can be activated by any Switch, Stick or Knob
position. Switch setting enables you to set the points when your
desired function/timer/telemetry can be turned ON or OFF.
Various functions can be activated by any Switch, Stick or Knob
position. Switch setting enables you to set the points when your
desired function/timer/telemetry can be turned ON or OFF.
1.
Switch & Stick Type
The first menu line item lists the control’s number and the second
item lists the type of control element. Using the “F2” and “F3”
function buttons you can scroll through channels, with the “F5 (Ok)”
button you can exit the menu screen.
item lists the type of control element. Using the “F2” and “F3”
function buttons you can scroll through channels, with the “F5 (Ok)”
button you can exit the menu screen.
2.
Switch ON/OFF Points
Any proportional function can be set as a system switch. This menu
item enables you to assign the travel percentage at which a desired
function can be turn ON or OFF.
“Switch-ON” – The point when the control element positon will
switch a function ON.
“Switch-OFF” – The point when the control element positon will
switch a function OFF.
By default, the system setting for all proportional channels and for all
inputs is set to function the same as a 3-position switch.
item enables you to assign the travel percentage at which a desired
function can be turn ON or OFF.
“Switch-ON” – The point when the control element positon will
switch a function ON.
“Switch-OFF” – The point when the control element positon will
switch a function OFF.
By default, the system setting for all proportional channels and for all
inputs is set to function the same as a 3-position switch.
a)
A function above this point is considered to be “Switch ON”
b)
A function in this range (middle) can be considered to be either
“Switch ON” or “Switch OFF”
c)
A Function below this point is considered to be“Switch OFF”
If the switch setting is set at same level for “Switch ON” and “Switch
OFF” the proportional channel/function output will be the same as a
2-position switch.
OFF” the proportional channel/function output will be the same as a
2-position switch.
3.
Required Preflight Position
For any functions assigned to the Switch, Knob or Stick; any preflight
initial position can be programmed. If the pre-programed Switches,
Knobs or Sticks are not in required preflight position while model is
being activated, system will refuse to switch to this model. The
transmitter screen will display the function that is not in pre-
programmed, correct preflight position.
initial position can be programmed. If the pre-programed Switches,
Knobs or Sticks are not in required preflight position while model is
being activated, system will refuse to switch to this model. The
transmitter screen will display the function that is not in pre-
programmed, correct preflight position.
4.
Function Status Display
Position and status of the control is displayed in the status bar. On
the right side of this menu you can see status of the switch function
the right side of this menu you can see status of the switch function
1
2
3
4
63