Справочник Пользователя для Arkon CDA-118M
34
-EN
The setting of Parametric EQ/Graphic EQ Adjustment, Time Correction
and X-Over can be adjusted in this mode.
and X-Over can be adjusted in this mode.
Adjusting the Parametric Equalizer Curve
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste. To adjust the Parametric Equalizer
Curve, set the EQ mode to PARAMETRIC EQ. For details, refer to
“Setting EQ mode” (page 36).
appealing to your personal taste. To adjust the Parametric Equalizer
Curve, set the EQ mode to PARAMETRIC EQ. For details, refer to
“Setting EQ mode” (page 36).
1
After selecting EQ ADJ (Parametric EQ) from the
Sound Field Adjustment mode, turn the Rotary
encoder to select the band adjustment, and then
press
Sound Field Adjustment mode, turn the Rotary
encoder to select the band adjustment, and then
press
/ENTER.
BAND1
BAND2
BAND3
BAND4
BAND5
BAND1
2
Turn the Rotary encoder to select an item to
adjust, then press
adjust, then press
/ENTER.
Frequency Adjustment
3
-1 Turn the Rotary encoder to select frequency
bands.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
20 Hz to 20 kHz (in 1/3 octave steps)
BAND1: 20 Hz~80 Hz (63 Hz)
BAND2: 50 Hz~200 Hz (150 Hz)
BAND3: 125 Hz~3.2 kHz (400 Hz)
BAND4: 315 Hz~8 kHz (1 kHz)
BAND5: 800 Hz~20 kHz (2.5 kHz)
Level Adjustment
3
-2 Turn the Rotary encoder to adjust the level.
Adjustable level: –6 to +6 dB
Bandwidth (Q) Adjustment
3
-3 Turn the Rotary encoder to set the bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
4
To adjust another band, repeat steps 1 to 3 and
adjust all bands.
adjust all bands.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the Parametric EQ, you should consider the
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
Adjusting the Graphic Equalizer Curve
You can modify the equalizer settings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ mode to GRAPHIC EQ. For details, refer to “Setting EQ
mode” (page 36).
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ mode to GRAPHIC EQ. For details, refer to “Setting EQ
mode” (page 36).
1
After selecting EQ ADJ (Graphic EQ) from the Sound
Field Adjustment mode, turn the Rotary encoder
to select the band adjustment, and then press
Field Adjustment mode, turn the Rotary encoder
to select the band adjustment, and then press
/ENTER.
BAND1
BAND2
BAND3
BAND4
BAND5
BAND6
BAND7
BAND1
BAND-1 (63 Hz) / BAND-2 (150 Hz) / BAND-3 (400 Hz) /
BAND-4 (1 kHz) / BAND-5 (2.5 kHz) / BAND-6 (6.3 kHz) /
BAND-7 (17.5 kHz)
2
Press
/ENTER to activate the level adjusting
mode.
3
Turn the Rotary encoder to adjust the level.
Adjustable output level: –6 to +6 dB
4
To adjust another band, repeat steps 1 to 3, and then
adjust all bands.
adjust all bands.
Adjusting the Time Correction
Before performing the following procedures, refer to “About Time
Correction” (page 37).
Correction” (page 37).
1
After selecting TIME CORRECTION from the Sound
Field Adjustment mode, turn the Rotary encoder
to select the band adjustment, and then press
Field Adjustment mode, turn the Rotary encoder
to select the band adjustment, and then press
/ENTER.
2.2ch (3WAY) System
4.2ch (FRONT/REAR/SUBW.) System
2
Press
/ENTER to activate the Time Correction
input mode.
3
Turn the Rotary encoder to adjust the distance (0.0
to 336.6 cm).
to 336.6 cm).
L = (distance to farthest speaker) – (distance to other
speakers)
Refer to “Time Correction Value List” on page 37.
4
Repeat steps 1 to 3 to set another speaker.
Set these values to achieve simultaneous sound
propagation to the listening position.
propagation to the listening position.
Sound Field Adjustment
FC
LV
Q
FC
(frequency) (level) (bandwidth) (frequency)
F-L (Initial setting)
F-R
R-L
R-R
(Mid-L)
(Mid-R) (High-L ) (High-R)
SW-L
SW-R
F-L
(Mid-L)
F-L (Initial setting)
F-R
R-L
R-R
(Front-L)
(Front-R) (Rear-L) (Rear-R)
SW-L
SW-R
F-L
(Front-L)