Справочник Пользователя для IFB Appliances AW60-806

TROUBLE SHOOTING

No indication

in controller

The power plug is not plugged tight.

The power switch is not switched 

on.

Not press 

 

 "START/PAUSE" button.

Power cut.

Re-plug the power plug.

Check the power socket, or change other 

socket.

Press 

 

 "START/PAUSE" button.

Wait for switching on electricity.

The inlet hose

.leakage

Do not rightly connect the tap with 
the universal connector.
Do not screw tight the nut of the 
water inlet hose.

Re-install rightly  the universal connector.

Screw tight the nut.

Does not drain

The drain hose is wrung or jammed.

Loosen the drain hose for smooth flow 
 of water

Dose not inject water

Stop water.

Do not open the tap.

Whether the wire netting in the water

inlet was stopped up by the sundries.

Wait for coming water.

Open the tap.

Clean the netting according to the method of 

"Cleaning of the water inlet". 

Spinning stops and 

water injecting begains

in the course of spin

Cause by that the washing 

This is automatic rectification for spinning 
in the washing program. That the washing 
are too much or too little, or that the 
washing machine is not placed plane will 
cause the unbalance in time of spinning. If 
there is still abnormal circumstances after 
checking the above-mentioned points, 
please pull out the power plug  and contact 
with local service as soon as possible.    

Does not spin

After end to drain, do not close the lid.

Open the lid in course of spinning.

Close the upper lid.

 

Intermittent spinning

In order to attain the better 

spinning effect.

Belong to the normal 
phenomenon generally.

Before using the machine

water exists in the drain 

hose.

Remainning  water due to testing 

or experiment in the  factory.

Belong to the normal 
phenomenon generally.

The washing machine does not work normally because the voltage is low or too high. Please pull 

out the plug and wait till the voltage becomes normal.

If there is still abnormal circumstances after checking the above-mentioned points, please pull out 

the plug. Do not repair it by yourself at home, which is very dangerous.

METHOD OF MAINTENANCE

1.There is water injection in time of washing or rinse, which is due to that the washer senses the 

inadequacy of water and exchanges water level automatically.

2.There is the phenomenon of intermittent spinning in the beginning of spinning, which is performed 

to achieve better spinning effects.

3. In the course of spin, the program return to the wash program. Because that is designed to rectify 

the unbalanced distribution of load in the spin tub.

The washing machine will send off the "DOU-
DOU"sound after any program operation to 
remind you of taking out the load or going on 
with other operations.

After finishing washing, please shut off the tap, 
pull out the plug in case of water leakage or fire 

Use soft cloth to wipe off the 
water and dirt on the surface 
each time after use of the 
washing machine.  Detergent, 
propellant and other chemicals 
are not allowed to use, for they 
can cause damage to the 
surface.

   After long time use, the water inlet mesh bag may 
be blocked with smudginess, and should be 
cleaned according to the following steps:
1. Switch on the power, followed by shutting off the 
tap .
2. Let the washer works for 5 seconds so that water 
flows into the tub through the water inlet hose. then 
turn off the power.
3. Unload the water inlet hose and clean the mesh 
bag, then restore the water inlet assembly.

    A f t e r   u s i n g   t h e  
washing machine for a 
period, please clean 
according the following 
steps:

1. Take out the lint filter.
2. Turn the mesh bag 
outside and wash it 
clean in the water.
3. Restore it and refix it.

Clasper

Slot