Инструкции Пользователя для Beltronics Pro 200
Power Connection
To power your Pro200, plug the small
end of the power cord, (telephone-type
connector) into the modular jack on the
Pro200’s right side, and plug the lighter
plug adapter into your vehicle’s lighter
socket or accessory socket.
end of the power cord, (telephone-type
connector) into the modular jack on the
Pro200’s right side, and plug the lighter
plug adapter into your vehicle’s lighter
socket or accessory socket.
Your Pro200 operates on 12 volts DC
negative ground only. The lighter plug
provided is a standard size and will work
in most vehicles. However, some vehicles
may require the optional European sleeve
to ensure a snug fit. If so, simply call our
service department to order one. This
sleeve slides over the lighter plug. Of
course, your lighter socket must be clean
and properly connected for proper
operation.
negative ground only. The lighter plug
provided is a standard size and will work
in most vehicles. However, some vehicles
may require the optional European sleeve
to ensure a snug fit. If so, simply call our
service department to order one. This
sleeve slides over the lighter plug. Of
course, your lighter socket must be clean
and properly connected for proper
operation.
NOTE: Depending on your vehicle, the
lighter socket power may either be
continuously on, or it may be switched on
and off with your ignition switch.
lighter socket power may either be
continuously on, or it may be switched on
and off with your ignition switch.
Optional power cords
See the Accessories section for details on
our optional SmartCord or Direct-wire
power cords. Page 25
See the Accessories section for details on
our optional SmartCord or Direct-wire
power cords. Page 25
Mounting Location
WARNING: Beltronics cannot anticipate the
many ways the Pro200 can be mounted.
It is important that you mount your Pro200
where it will not impair your view nor
present a hazard in case of an accident.
many ways the Pro200 can be mounted.
It is important that you mount your Pro200
where it will not impair your view nor
present a hazard in case of an accident.
Where to mount your Pro200
For optimum detection performance, we
recommend the following:
For optimum detection performance, we
recommend the following:
• Using the QuickMount bracket, mount
your Pro200 level, and high enough on
your front windshield to provide a clear
view of the road from the front and rear.
your Pro200 level, and high enough on
your front windshield to provide a clear
view of the road from the front and rear.
• Mount the Pro200 away from windshield
wipers, other solid objects, and heavily
tinted areas that might obstruct the radar
antenna or laser lens.
wipers, other solid objects, and heavily
tinted areas that might obstruct the radar
antenna or laser lens.
6
Installation
7
Caution!
A few vehicles (including some Porsches)
have windshields with a soft anti-lacerative
coating on the inside surface. Use of
suction cups will permanently mar this
coating. Consult your dealership or the
vehicle owner’s manual to determine if
your windshield has this coating.
A few vehicles (including some Porsches)
have windshields with a soft anti-lacerative
coating on the inside surface. Use of
suction cups will permanently mar this
coating. Consult your dealership or the
vehicle owner’s manual to determine if
your windshield has this coating.
User’s Tip
You can leave the QuickMount bracket in
place on your windshield, and easily
remove the Pro200 by pressing the
adjustment button and sliding the Pro200
off the mount. Again, be sure to position the
bracket where it won’t present a hazard in
the event of an accident. Additional mounts
are available.
You can leave the QuickMount bracket in
place on your windshield, and easily
remove the Pro200 by pressing the
adjustment button and sliding the Pro200
off the mount. Again, be sure to position the
bracket where it won’t present a hazard in
the event of an accident. Additional mounts
are available.
Windshield QuickMount
The Pro200’s QuickMount bracket is
designed for unobtrusive and hassle-free
mounting.
designed for unobtrusive and hassle-free
mounting.
1 Depress the QuickMount button on
the top of the Pro200 (by the word
BELTRONICS) and slide the QuickMount
bracket into the slot until it is locked into
the position which best fits the angle of
your windshield (there are four settings
available). For extremely horizontal
or extremely sloped windshields,
the QuickMount bracket can
be bent.
the top of the Pro200 (by the word
BELTRONICS) and slide the QuickMount
bracket into the slot until it is locked into
the position which best fits the angle of
your windshield (there are four settings
available). For extremely horizontal
or extremely sloped windshields,
the QuickMount bracket can
be bent.
To ensure that the suction cups
adhere to the windshield firmly, be sure to
keep both your windshield and the suction
cups clean.
adhere to the windshield firmly, be sure to
keep both your windshield and the suction
cups clean.
2 To adjust the Pro200 on your
windshield, use the QuickMount
adjustment button located on the top of
the Pro200, and slide the Pro200 forward or
backward to obtain a level horizontal
position.
When installed and adjusted properly, the
back top edge of the Pro200 should rest
solidly against your windshield.
windshield, use the QuickMount
adjustment button located on the top of
the Pro200, and slide the Pro200 forward or
backward to obtain a level horizontal
position.
When installed and adjusted properly, the
back top edge of the Pro200 should rest
solidly against your windshield.