Справочник Пользователя для Brother 882-W02
TROUBLESHOOTING
330
TROUBLESHOOTING
If you have a minor problem with your sewing machine, check the following solutions. If the solutions
suggested do not correct the problem, contact your authorized dealer. Press
o
o
for advice about minor sewing problems during sewing. Press
at any time to return to
the original screen. If you need additional help, the Brother Solutions Center offers the latest FAQs and
troubleshooting tips. Visit us at [http://solutions.brother.com].
If the problem persists, contact your dealer or the nearest authorized service center.
Problem
Cause
Solution
Page
The thread is tangled
on the wrong side of
the fabric.
on the wrong side of
the fabric.
Upper threading is incorrect.
Check the steps for threading the machine
and rethread the machine.
and rethread the machine.
46
Using improper needle or thread for the
selected fabric.
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
Combinations” chart.
58
The upper thread is
too tight.
too tight.
The bobbin thread is incorrectly installed.
Correctly install the bobbin thread.
43
Cannot thread the
needle
needle
Needle is not in the correct position.
Press the “Needle Position” button to raise the
needle.
needle.
3
Needle is installed incorrectly.
Reinstall the needle correctly.
56
Needle is turned, bent or the point is dull.
Replace the needle.
56
Cannot lower the
presser foot with the
presser foot lever
presser foot with the
presser foot lever
Presser foot was raised using the “Presser Foot
Lifter” button.
Lifter” button.
Press the “Presser Foot Lifter” button to lower
the presser foot.
the presser foot.
3
Thread tension is
incorrect
incorrect
Upper threading is incorrect.
Check the steps for threading the machine
and rethread the machine.
and rethread the machine.
46
Bobbin is set incorrectly.
Reset the bobbin. (If needle plate was
removed, reinstall needle plate and tighten
screws prior to installing bobbin case.)
removed, reinstall needle plate and tighten
screws prior to installing bobbin case.)
43
Using improper needle or thread for the
selected fabric.
selected fabric.
Check the “Fabric/Thread/Needle
Combination” chart.
Combination” chart.
58
Presser foot holder is not attached correctly.
Reattach the presser foot holder correctly.
55
Thread tension is set incorrectly.
Adjust the thread tension.
67, 227
Bobbin thread is incorrectly wound.
Use a correctly wound bobbin.
37
Needle is turned, bent or the point is dull.
Replace the needle.
56
Upper thread breaks
Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Rethread the machine correctly.
46
Needle is turned, bent or the point is dull.
Replace the needle.
56
There are scratches on the race.
Replace the race, or consult your authorized
dealer.
dealer.
326
Upper thread tension is too strong.
Adjust the thread tension.
67, 227
Using improper needle or thread for the
selected fabric.
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
Combinations” chart.
58
Thread is twisted.
Use scissors, etc., to cut the twisted thread
and remove it from the race, etc.
and remove it from the race, etc.
—
There are scratches near the hole of the needle
plate.
plate.
Replace the needle plate, or consult your
authorized dealer.
authorized dealer.
86
There are scratches near the hole in the presser
foot.
foot.
Replace the presser foot, or consult your
authorized dealer.
authorized dealer.
54
Needle is installed incorrectly.
Reinstall the needle correctly.
56
Thread is knotted or tangled.
Rethread upper and lower thread.
43, 46
A bobbin designed specifically for this machine
is not used.
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
use a bobbin designed specifically for this
machine.
43