Инструкции Пользователя для Behringer B-Control Fader BCF2000

B-CONTROL FADER BCF2000/ROTARY BCR2000 User Manual

MMC:
MIDI Machine Control data is only assignable to button elements.
Encoder 4 (Value 1) sets “Locate Time” hour and minute values, while encoder 5 

(Value 2) sets seconds and frames. The Locate Position is always sent before the 

MMC command. We therefore have the following logic-switching sequence:
If the “Locate” parameter has been selected, the sequencer or hard drive recorder 

always jumps to the set position. If “Play” has been selected as the parameter 

(for a button), the sequencer always starts from the set locator point as soon 

as the button is pressed. “Rewind” always begins at the chosen locator point. 

Select the frame rate with encoder 6: 24, 25, 30 (non-drop), 30d (drop frame) 

or “off” (in this case only the MMC message is sent, without any information of 

the locate position).

GS / XG:
Encoder 3 directly selects the most important “Main Control” parameters. 

The display indicates them as a (shortened) text (table 4.2). In this case, these are 

CCs or NRPNs (no SysEx data).

Filter Cutoff

NRPN

CUTF

Filter Resonance

NRPN

RESO

Vibrato Rate

NRPN

RATE

Vibrato Depth

NRPN

DEPT

Vibrato Delay

NRPN

DLY

EG Attack

NRPN

ATC

EG Decay

NRPN

DCY

EG Release

NRPN

RELS

Modulation

CC 1

MODU

Portamento Time

CC 5

PORT

Volume

CC 7

VOL

Pan

CC 10

PAN

Reverb Send

CC 91

REVB

Chorus Send

CC 93

CRS

Delay / Variation Send

CC 94

VARS

Table 4.3: GS / XG Parameter Main Controls

Encoders 4 and 5 let you confine or invert each controllers’ value range.

Settings that have an effect on all presets are made in the global setup menu.

Keep the EDIT key pressed and at the same time press the STORE key

You are now in the global setup menu, and can let go of both keys

Now, turn the push encoders 1 to 8 to get the desired setting. This is how the 

push encoders are allocated

1

Operating Mode

U-1 ... U-4, S-1 ... S-4

2

Global RX Channel

Off, 1 ... 16

3

Footswitch

Auto / Normal / Inverted

4

Start-Preset

1 ... 32, Last

5

Device ID

1 ... 16

6

SysEx Dump

Single/All

7

—

—

8

MIDI Data Interval

(ms)

Table 4.4: Push encoder allocation in global setup menu

To exit the global setup menu, press EXIT

The settings in the global setup menu take effect immediately and do not 

have to be separately stored

Operating Mode:
The operating modes are described in chapter 4.1. You can select USB modes 

U-1 to U-4 and stand-alone modes S-1 to S-4.

Global RX Channel:
The B-CONTROL receives program change commands on this channel.

Footswitch type:
Because there are different kinds of footswitches (depending on their switching 

behavior), the polarity of the footswitch connector can be set (normal / inverted), 

or it can be automatically detected during power startup (auto recognition).

Start Preset Number:
Each of the 32 presets can be selected as the startup preset. Additionally, with 

the “Last” function, at startup you have the option to always load the preset that 

was used last.

Device ID Number:
You should change the ID number settings only if you work with several 

BCF2000s or BCR2000s at the same time, and problems with recognizing the 

correct device start occurring during a SysEx Dump procedure.

SysEx Dump Select:
Turning push encoder 6 lets you select between the current preset (single) or the 

entire memory contents of the 32 presets (all) should be sent as a SysEx dump. 

One press on encoder 6 triggers the dump.
To receive a SysEx dump, you don’t have to change any settings on your 

equipment. If you send a single preset to the B-CONTROL, the data is written to 

a temporary memory; to be stored permanently, the data has to be stored on a 

storage slot of your choice (preset store function).

To cancel a SysEx dump, press the EXIT key

MIDI Data Interval:
This is where you adjust the data transmission rate. This setting only has an 

effect on MIDI data packs such as SysEx dumps and not on controlling of MIDI 

commands (they are carried out in real time anyway). The transmission rate is 

adjustable in milliseconds.