Инструкции По Установке для White Rodgers 11D31-1 Well Immersion Single Control
Printed in U.S.A.
WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS RD., ST. LOUIS, MO. 63123
(314) 577-1300, FAX (314) 577-1517
EMERSON ELECTRIC CO.
9797 REAVIS RD., ST. LOUIS, MO. 63123
(314) 577-1300, FAX (314) 577-1517
9999 HWY. 48, MARKHAM, ONT. L3P 3J3
(905) 475-4653, FAX (905) 475-4625
(905) 475-4653, FAX (905) 475-4625
THESE CONTROLS MUST BE INSTALLED BY A QUALIFIED
INSTALLER.
INSTALLER.
Do not exceed the specification ratings.
All wiring must conform to local and national electrical codes
and ordinances.
and ordinances.
This control is a precision instrument, and should be handled
carefully. Rough handling or distorting components could cause
the control to malfunction.
carefully. Rough handling or distorting components could cause
the control to malfunction.
This control has been accurately calibrated at the factory. Any
attempt to calibrate this control will void the White-Rodgers
warranty.
attempt to calibrate this control will void the White-Rodgers
warranty.
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE.
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE.
11D05, 11D18, 11D31, 11D55
WELL IMMERSION
HOT WATER CONTROL
INSTALLATION INSTRUCTIONS
These controls are designed for use on hot water heating
installations. They have; open on rise, close on rise, or S.P.D.T.
switch action and are available with either fixed or adjustable
differential.
installations. They have; open on rise, close on rise, or S.P.D.T.
switch action and are available with either fixed or adjustable
differential.
These controls are shipped with the bulb and capillary in the
horizontal position. Some of these models also have excess
capillary stored within the enclosure permitting them to be used
with wells having either a standard or extended shank.
horizontal position. Some of these models also have excess
capillary stored within the enclosure permitting them to be used
with wells having either a standard or extended shank.
Another model is available with open-on-rise manual reset
feature. Most controls can be used on either horizontal or
vertical well installation.
feature. Most controls can be used on either horizontal or
vertical well installation.
PRECAUTIONS
DESCRIPTION
To prevent electrical shock and/or equipment dam-
age, disconnect electric power to system, at main fuse
or circuit breaker box, until installation is complete.
age, disconnect electric power to system, at main fuse
or circuit breaker box, until installation is complete.
CAUTION
Some controls have excess stored capillary which may be ex-
tended for use with an extended shank well. Use reasonable care
when straightening and forming the capillary.
tended for use with an extended shank well. Use reasonable care
when straightening and forming the capillary.
With the capillary fully extended, the bulb should slide all the way
to the end of the well.
to the end of the well.
EXTENDING CAPILLARY
Do not use on circuits exceeding specified voltages.
Higher voltages will damage control and could cause
shock or fire hazard.
Higher voltages will damage control and could cause
shock or fire hazard.
WARNING
CONVERTIBLE CONTROLS
Convertible controls have a knockout plate on back of case
(secured by 2 screws that hold well clamp). To convert from
Horizontal to Vertical:
(secured by 2 screws that hold well clamp). To convert from
Horizontal to Vertical:
1. Remove control cover.
2. Loosen 2 clamp screws.
3. Swing capillary down through slot into bottom knockout.
4. Secure knockout plate to back of case by sliding screws
through keyhole slots on bottom of case.
CONVERSION ADAPTER
CAPILLARY
BULB
WHITE-RODGERS
Operator: Save these instructions for future use!
PART NO. 37-2561B
Replaces 37-2561A & 37-9461
9549