Справочник Пользователя для Vortech Engineering Nissan 350Z/Infinity G35Supercharger System 2003-2006
P/N: 4NZ020-010
©2007 Vortech Engineering, LLC
All Rights Reserved, Intl. Copr. Secured
12JAN07 v4.0 Nissan 350Z(4NZv4.0)
6
A.
Install the supplied Ø1/2" fabric-braid oil drain
line onto the supercharger fitting and tighten
the supplied hose clamp.
line onto the supercharger fitting and tighten
the supplied hose clamp.
B.
Install the supplied 1/8"NPT x -4 straight fitting
into the supercharger oil feed nozzle using
motor oil on the threads. Attach the supplied
oil feed hose to the fitting and tighten.
into the supercharger oil feed nozzle using
motor oil on the threads. Attach the supplied
oil feed hose to the fitting and tighten.
NOTE:
Oil in the supercharger is gravity drained
to the oil pan. Trim the supplied oil drain
hose as necessary so that it is continu-
ously sloping down towards the oil pan.
Avoid dips, kinks, etc.
NOTE:
Use clean oil on the pipe (tapered)
threads. Teflon tape or sealant is not rec-
ommended as it may loosen and cause
blockage of the small oil feed orifice
resulting in supercharger failure.
NOTE:
2003-2005 standard output engine only.
(For 2005 and later high-output 300hp
engines, skip to Section 6.)
C.
Install the six mounting screws and washers
through the mounting plate in the positions
shown. (See Fig. 5-a.)
through the mounting plate in the positions
shown. (See Fig. 5-a.)
D.
Install the supercharger onto the mounting
plate and install and tighten the four 3/8" x 1"
screws and washers.
plate and install and tighten the four 3/8" x 1"
screws and washers.
E.
Install the supplied gilmer (toothed) belt
around the pulleys on the mounting plate
assembly. (See Fig. 5-b.)
around the pulleys on the mounting plate
assembly. (See Fig. 5-b.)
F.
Install the four supplied spacers onto their
respective screws. (See Fig. 5-b.) A small
dab of sealant between the spacer and the
mounting plate may help retain them during
the following steps.
respective screws. (See Fig. 5-b.) A small
dab of sealant between the spacer and the
mounting plate may help retain them during
the following steps.
G.
Position the supercharger mounting plate
assembly in front of the engine and start all
of the mounting screws.
assembly in front of the engine and start all
of the mounting screws.
H.
Make sure that the coolant hose is routed in
the groove on the back of the supercharger
mounting plate.
the groove on the back of the supercharger
mounting plate.
I.
Verify that the oil drain hose is routed as
smoothly as possible and connect it to the fit-
ting on the oil pan. Tighten a hose clamp on
this connection. Secure the oil drain hose and
the A/C line away from the A/C pulley with
zip-ties. Trim drain hose length if necessary.
smoothly as possible and connect it to the fit-
ting on the oil pan. Tighten a hose clamp on
this connection. Secure the oil drain hose and
the A/C line away from the A/C pulley with
zip-ties. Trim drain hose length if necessary.
J.
Route the oil feed hose outside the driver’s
side frame rail and then to the fitting installed
near the oil filter and tighten. Use the sup-
plied zip-ties to secure.
side frame rail and then to the fitting installed
near the oil filter and tighten. Use the sup-
plied zip-ties to secure.
K.
Tighten all of the mounting plate screws.
L.
Install the air filter onto the supercharger inlet
and tighten the clamp.
and tighten the clamp.
5.
SUPERCHARGER MOUNTING PLATE INSTALLATION..(2003-2005 Standard
Out-put Engines Only.) ( For 2005 and Later “Rev-Up” Engines, Skip to
Section 6.)
Out-put Engines Only.) ( For 2005 and Later “Rev-Up” Engines, Skip to
Section 6.)
Fig. 5-a
Fig. 5-b
M6 x 20mm
M12 x 40mm
M12 x 110mm
M6 x 25mm
M6 x 70mm
M12 x 50mm
Ø.5" x .254" SPACER
Ø1.0" x .602"
SPACER
Ø.5" x 1.175" SPACERS
Fig. 5-c