Справочник Пользователя для Vivitek 51" Micro Display Projection TV
WARNING:
The cooling fan in the REAR PROJECTION TV continues to run for about 150 seconds before the REAR
PROJECTION TV enters the standby mode. During normal Operation, when putting the REAR PROJECTION TV
into standby mode always use the POWER button on the REAR PROJECTION TV or on the remote control. Ensure
the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN
THE TELEVISION OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS COULD RESULT IN
PREMATURE LAMP FAILURE.
PROJECTION TV enters the standby mode. During normal Operation, when putting the REAR PROJECTION TV
into standby mode always use the POWER button on the REAR PROJECTION TV or on the remote control. Ensure
the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN
THE TELEVISION OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS COULD RESULT IN
PREMATURE LAMP FAILURE.
WARNING :
EYE DAMAGE MAY RESULT FROM DIRECTLY VIEWING THE LIGHT PRODUCED BY THE LAMP USED
IN THIS APPARATUS. ALWAYS TURN OFF LAMP BEFORE OPENING THIS COVER.
IN THIS APPARATUS. ALWAYS TURN OFF LAMP BEFORE OPENING THIS COVER.
LAMP REPLACEMENT WARNING :
REFER TO THE INSTRUCTION MANUAL BEFORE REMOVING THE SCREW, DISCONNECT POWER
CORD. HOT SURFACE INSIDE. ALLOW 45 MINUTES TO COOL BEFORE REPLACING THE LAMP.
REPLACE WITH SAME LAMP UNIT ONLY.
THIS COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE
ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF
LAMP HAS RUPTURED. HANDLE WITH CARE.
CORD. HOT SURFACE INSIDE. ALLOW 45 MINUTES TO COOL BEFORE REPLACING THE LAMP.
REPLACE WITH SAME LAMP UNIT ONLY.
THIS COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE
ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF
LAMP HAS RUPTURED. HANDLE WITH CARE.
iii
Potential hazard of glass particles if lamp ruptures.
In case of lamp rupture, contact your nearest
Authorized Projector Dealer or Service Center for a
replacement. See "Replacing the Lamp" on Page 31
In case of lamp rupture, contact your nearest
Authorized Projector Dealer or Service Center for a
replacement. See "Replacing the Lamp" on Page 31
Replacement Lamp Part Numbers:
UHP (120W Lamp) RP51
UHP (120W Lamp) RP51
USER SERVICE SCREW.
VIS POUR ENTRETIEN PAR
L'UTILISATEUR.
VIS POUR ENTRETIEN PAR
L'UTILISATEUR.
Caution Concerning Lamp Replacement
See "Replacing the Lamp" on Page 31,32
See "Replacing the Lamp" on Page 31,32
WARNING
EYE DAMAGE MAY RESULT FROM DIRECTLY VIEWING THE LIGHT PRODUCED BY THE LAMP
USED IN THIS APPARATUS. ALWAYS TURN OFF LAMP BEFORE OPENING THIS COVER.
USED IN THIS APPARATUS. ALWAYS TURN OFF LAMP BEFORE OPENING THIS COVER.
WARNING
EYE DAMAGE MAY RESULT FROM DIRECTLY VIEWING THE LIGHT PRODUCED BY THE LAMP
USED IN THIS APPARATUS. ALWAYS TURN OFF LAMP BEFORE OPENING THIS COVER.
USED IN THIS APPARATUS. ALWAYS TURN OFF LAMP BEFORE OPENING THIS COVER.
LAMP REPLACEMENT WARNING
REFER TO THE INSTRUCTION MANUAL BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT
SURFACE INSIDE. ALLOW 45 MINUTES TO COOL BEFORE REPLACING THE LAMP.REPLACE WITH SAME LAMP
UNIT ONLY. THIS COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET
RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS
RUPTURED. HANDLE WITH CARE.
SURFACE INSIDE. ALLOW 45 MINUTES TO COOL BEFORE REPLACING THE LAMP.REPLACE WITH SAME LAMP
UNIT ONLY. THIS COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET
RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS
RUPTURED. HANDLE WITH CARE.
LAMP REPLACEMENT WARNING
REFER TO THE INSTRUCTION MANUAL BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT
SURFACE INSIDE. ALLOW 45 MINUTES TO COOL BEFORE REPLACING THE LAMP.REPLACE WITH SAME LAMP
UNIT ONLY. THIS COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET
RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS
RUPTURED. HANDLE WITH CARE.
SURFACE INSIDE. ALLOW 45 MINUTES TO COOL BEFORE REPLACING THE LAMP.REPLACE WITH SAME LAMP
UNIT ONLY. THIS COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET
RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS
RUPTURED. HANDLE WITH CARE.