Справочник Пользователя для United States Stove 2020N
If the knob does not pop up when re-
leased, stop and immediately call your
service technician or gas supplier. If the
pilot will not stay lit after several tries, turn
control knob to "OFF" and call your gas
supplier.
leased, stop and immediately call your
service technician or gas supplier. If the
pilot will not stay lit after several tries, turn
control knob to "OFF" and call your gas
supplier.
9.
Turn valve knob clockwise to "ON".
10. Wait about one minute then turn burner
switch (D) to "ON". It will take a few
minutes for the thermopile located on top
of the pilot to heat up.
minutes for the thermopile located on top
of the pilot to heat up.
NOTE: If unit is equipped with remote "on-off"
wall switch, switch must be in "on" position for
burner to light.
wall switch, switch must be in "on" position for
burner to light.
11. Adjust flame height with the high-low
knob(C).
12. Turn on all electrical power to the appli-
ance.
13. Close access door.
NOTE: It is normal for the new heater to give
off some odor the first time it is burned. This is
due to the curing of the paint and any undetec-
ted oil from the manufacturing process.
It is recommended that you burn your new
heater for at least two(2) hours the first time
you use it. If optional fan kit is installed, leave
it turned off for the break in period.
off some odor the first time it is burned. This is
due to the curing of the paint and any undetec-
ted oil from the manufacturing process.
It is recommended that you burn your new
heater for at least two(2) hours the first time
you use it. If optional fan kit is installed, leave
it turned off for the break in period.
OPERATING INSTRUCTIONS,
CONTINUED
1.
Open access door.
2.
Turn switch (D) to "OFF"
3.
Unplug all electric power if service is to be performed.
4.
Push in gas control knob slightly and turn clockwise to the "OFF" position.
5.
Close access door.
TURN OFF GAS TO APPLIANCE
TURN OFF GAS TO APPLIANCE
TURN OFF GAS TO APPLIANCE
TURN OFF GAS TO APPLIANCE
TURN OFF GAS TO APPLIANCE
16
1.
STOP! Read the safety information on
the previous page.
the previous page.
2.
Set the thermostat to lowest setting.
3.
Turn off all electrical power and open the
access door.
access door.
4.
Push in gas control (B) slightly and turn
clockwise to "OFF".
clockwise to "OFF".
5.
Push "ON / OFF" switch to "OFF" posi-
tion.
tion.
NOTE: Knob cannot be turned from "PILOT"
to "OFF" unless knob is pushed in slightly. Do
not force.
to "OFF" unless knob is pushed in slightly. Do
not force.
6.
Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the
floor. If you smell gas, STOP! Follow "B"
in the safety information on the previous
page. If you don't smell gas, go on to the
next step.
Then smell for gas, including near the
floor. If you smell gas, STOP! Follow "B"
in the safety information on the previous
page. If you don't smell gas, go on to the
next step.
7.
Depress knob (B) and turn gas control
knob counterclockwise to "Pilot".
knob counterclockwise to "Pilot".
8.
Push in knob (B) all the way and hold in.
Immediately light the pilot by pushing in
on the piezo button (A). Continue to hold
the control knob in for about one(1) minute
after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If
it goes out, repeat steps 4 through 8.
Immediately light the pilot by pushing in
on the piezo button (A). Continue to hold
the control knob in for about one(1) minute
after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If
it goes out, repeat steps 4 through 8.
LIGHTING INSTRUCTIONS
LIGHTING INSTRUCTIONS
LIGHTING INSTRUCTIONS
LIGHTING INSTRUCTIONS
LIGHTING INSTRUCTIONS
C
A
B
D
PILOT LOCATION
TOP VIEW OF BURNER ASSEMBLY