Справочник Пользователя для Skylink WR-001

Input Voltage: 120V AC, 60Hz   

Maximum Load: 600W at 120VAC 
Operating Frequency: 318MHz

Range: Up to 500 feet in open area

Standby Current: 0.2mA
Minimum Load: 10W

Operational Temperature: -4° F - 140° F 

(-20° C - 60° C)

Humidity: 5%-95%

The Device is approved by the FCC and it complies with Part 15 of the FCC Rules.  
Its operation is subject to the following two conditions : 
1.  This device may not cause harmful interference.
2.  This device must accept any interference that may cause undesired operation.

WARNING:
Changes or modifications to this unit not expressly approved by the party responsible 
of compliance could void the user’s authority to operate the equipment.

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com

P/N. 101Z713
Patent Pending
©2010 SKYLINK GROUP

You may erase a transmitter or sensor from the wall dimmer, but you 
cannot erase a specific device directly, you must erase all the wireless 
devices, then program the ones you want to keep.  Follow the instructions 
below to erase programmed transmitters / sensors.

1. Power off the Wall Dimmer by placing the air gap switch to off position. 
2. Press and hold the SET button, while holding the SET button, slide the 
    air gap switch to on position.
3. The blue LEDs will be on first, then flashes rapidly for 1 second.
4. You may release the SET button, now you have successfully erased all 
    the devices. 

The Skylink

 System consists of many other devices such as

SkylinkHome  Remotes, Motion Sensor, ON/OFF Wall Switch, Wall 
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF 
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control, 
ON/OFF Control, Smart Button Garage Door Control, etc. Please visit 
Skylink website at www.skylinkhome.com for more information. 

TM

Home

TM

TM  

V2.0

If, within one year from date of purchase, this product should become defective 
(except battery), due to faulty workmanship or materials, it will be repaired or 
replaced, without charge. Proof of purchase and a Return Authorization are required.

An optional deluxe remote is needed for zone operation. A Zone Command 
allows you to operate multiple lights altogether in the same zone.
A zone command must first be programmed to the receiver before zone 
operation.  To program a zone command, please refer to the user's 
instructions of the deluxe remote.

To turn on or off a zone, hold [        ] or [       ] until the red LED flashes 
three times and keeps on, then release the held button and press the 
zone number.  

For example: 

Hold [       ] until the red LED flashes three times and keeps on, then 
release [       ] and press [1], all lights in zone 1 will be turned on.

Hold [       ] until the red LED flashes three times and keeps on, then 
release [       ] and press [1], all lights in zone 1 will be turned off.

You can also change the brightness of lights in a zone altogether, if the 
receiver modules and all lights connected are dimmable. If non-dimmable 
lights or appliances are connected to a zone, do not operate Zone 
Brightness Control.

For example: 

Hold [       ] until the red LED flashes three times and keeps on, then 
release [       ] and hold [1] , all lights in zone 1 will be brightened, you 
may release [1] at the desired brightness level.

Hold [       ] until the red LED flashes three times and keeps on, then 
release [       ] and hold [1] , all lights in zone 1 will be dimmed, you 
may release [1] at the desired brightness level.

If you would like to 
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products 

or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax  (800) 286-1320