Справочник Пользователя для Security 100 KE-265

 

16 

To Program a New User Code or Change an Existing User 
Code: 

1.  Choose a new 3 to 8 digit code that will be used for this 

User Code.  

 

___ ___ ___ ___ ___ ___ ___ ___ 

2.  Decide which User Location to place this User Code 

(see Overview of User Codes) 

3.  Enter the Master Code, followed by the User Location 

(you will hear three rapid beeps) and immediately enter 
the new User Code. (Do not let more than five seconds 
elapse between entries or the system will reset!!!) 

Example: 1-3-5-7-9   1-1-1   1-2-3-4 

4.  After entering your new code, wait five seconds for the 

3 reset beeps. 

 

To Delete a User Code 

1.  Enter the Master Code, followed by the User Location 

of the User Code you want to delete (you will hear 
three rapid beeps). Example: 1-3-5-7-9    1-1-1 

2. 

Wait five seconds for the 3 reset beeps (Do not enter 
any digits until you hear 3 reset beeps)

 

Π5 seconds 

To Program/Change the Door Open Time for the Master Code 
and User Code 1 and 2: 

1.  First determine the length of time you wish to program 

as the Door Open Time for these users.  This is the 
length of time the door will remain open after a valid 
Master Code, User Code 1 or User Code 2 has been 
entered into the system.  
 Note: For controlling a garage door or electric gate, 
you will need to set the door open time to 1 second   

2.  Locate the Control Module, remove the cover and 

locate the “PROGRAM” switch on the circuit board. 

3.  Press the PROGRAM switch once *. (The Keypad will 

beep rapidly 4 times) 

4.  At the Keypad, enter 1-1-1-7 to open the memory (you 

will hear three rapid beeps) and enter a combination of 
“1’s” (for every one second increment) and  
 

 

17

 

“5’s”  (for every five second increment) that equal your 
desired Door Open Time. Each valid key press (a “1” or 
a “5”) will generate a double beep.  (Do not let more 
than five seconds elapse between entries or the 
system will reset!!!) 

Example: “1-1-1-7    5-5-5-1-1” 

Π17 seconds  

5.  After entering your Door Open Time, wait five seconds 

for the 3 reset beeps. 

 

To Program/Change the Door Open Time for User Code 3,4 
and 5: 

(Rev B and later) 

1.  First determine the length of time you wish to program 

as the Door Open Time for these users.  This is the 
length of time the door will remain open after a valid 
User Code 3, User Code 4 or User Code 5 has been 
entered into the system. 
 Note: For controlling a garage door or electric gate, 
you will need to set the door open time to 1 second.   

2.  Locate the Control Module, remove the cover and 

locate the “PROGRAM” switch on the circuit board. 

3.  Press the PROGRAM switch once *. (The Keypad will 

beep rapidly 4 times) 

4.  At the Keypad, enter 1-1-1-5 to open the memory (you 

will hear three rapid beeps) and enter a combination of 
“1’s” (for every one second increment) and “5’s”  (for 
every five second increment) that equal your desired 
Door Open Time. Each valid key press (a “1” or a “5”) 
will generate a double beep.  (Do not let more than five 
seconds elapse between entries or the system will 
reset!!!) 

Example: “1-1-1-5    1-1-5” 

Π7 seconds  

5.  After entering your Door Open Time, wait five seconds 

for the 3 reset beeps. 

 

 Notes: * Once the PROGRAM switch has been pressed, 
you have 2 minutes to begin programming. You will hear a 
double beep with each valid key press.  Once you begin 
entering the combination of 1’s and 5’s do not let more 
than five seconds elapse between entries or the system 
will reset!!! Maximum Door Open Time is 120 seconds

.