Справочник Пользователя для Russound CA4 Controller Kit CA4

Press and hold SET until the LED blinks twice.  

1. 

Press 9-7-6.

2. 

Press a source key twice to delete all the learned keys for that source. The LED blinks 

3. 

twice.
Repeat  step  3  for  another  key  for  a  device,  or  press  and  hold  SET  to  exit 

4. 

programming.

Press and hold SET until the LED flashes twice.  

1. 

Press SET, then 9-7-6 to delete a learned function. 

2. 

Press the source key once. 

3. 

Press  the  key  (twice)  containing  the  learned  function  to  be  deleted. The  remote 

4. 

blinks twice.
Repeat steps 2 to 4 for another key on the same source, or press and hold SET to exit 

5. 

programming.

Problem: LED blinks when you repress a key, but device does not respond. 

Solution: Make sure the remote is aimed at your device or system keypad and is not 

more than 15 feet away.

Problem: LED blinks one long blink. 

 

 

 

 

Solution: An entry error has occurred (i.e., wrong key). Try entry sequence again.

Problem: Remote does not control devices or commands are not working properly. 

Solution: Try  all  listed  codes  for  the  device.  Make  sure  the  device  operates  with  an 

infrared remote control.

Problem: Channels do not change properly. 

 

 

 

Solution:  If  the  original  remote  control  required  you  to  press  ENTER  to  change 

channels., press enter on this remote after entering the channel number.

Problem: LED does not blink when you press a key. 

 

 

 

Solution: Replace battery with two new AA batteries.

The CA4-RC includes a learning feature so you can add functions that are unique to your 

home entertainment devices (i.e., VCR tracking up or down). The following precautions 

apply. 

The original remote controls must be in working order for learning to work properly.

•

Learned keys are mode specific, so each one can store a unique function for each 

•

mode.
Do not use the following keys for learning: Device Keys, SET, Back, or Record.

•

Learning  capacity  is  approximately  16  to  25  keys,  depending  on  the  code  being 

•

learned.
Certain device codes are not learnable including multi-frequency types, some high 

•

frequency ones, and other unusual formats.
For optimum learning, avoid high levels of ambient light such as natural sunlight or 

•

energy-efficient fluorescent lights.
Have the original remote controls handy.

•

If more than 15 seconds pass between key presses, the remote exits programming.

•

Press and hold SET until LED flashes twice.

1. 

Press 9-7-5.

2. 

Press a source key once to assign a mode for learning.

3. 

Place the CA4-RC head-to-head (about 2” apart) from your original remote control. 

4. 

Also  locate  the  key  (on  original  remote  control)  that  will  serve  as  the  teaching 

function.
On the CA4-RC, press a key where the learned function will be stored.

5. 

On the original remote, press and hold the key to be learned. The CA4-RC LED will 

6. 

turn off. Continue holding the key on the original remote until the CA4-RC LED blinks 

twice.  Note: If the LED displays one long blink, a learning error has occurred. Try 

repeating this step again until a successful capture occurs. If the function is still not 

captured, press and hold SET to exit programming. Review the learning precautions 

listed above, or the Troubleshooting tips, before beginning again at step 1.
Repeat steps 4 to 6 for another key on same device, or repeat steps 1 to 6 for another 

7. 

device.