Листовка для Roland Skis V-4

 

The V-4 requires adjustment whenever the cross fader is replaced or the stroke is adjusted.

 

Connect the PREVIEW OUT jack on the V-4 to a television monitor (Fig. 1).

 

Turn on the power to the V-4. A light comes on in the gap with the cross fader.

 

Press the MENU button. The Menu screen appears on the television monitor (Figs. 2).

 

Press the [ ] or [ ] button to move the cursor to "Utility," then press the ENTER button.

 

Press the [ ] or [ ] button to select "Video Fader Calibrate A," then press the ENTER button.

 

Press the [ ] or [ ] button to select "Video Fader Calibrate B," then press the ENTER button.

 

Press the MENU button twice to quit the Menu screen.

 

■

 

You can adjust the cross fader to a stroke at any of four stages (10 mm, 23 mm, 35 mm, and 45 mm).

 

Move the control for the cross fader to its central position.

 

Using a Phillips screwdriver, remove the stopper retainer screw (Fig. 1).

 

Move the stopper to any one of the four holes that you prefer (Fig. 2).The four stopper holes are stamped 
"10," "23," "35," and "45." These indicate the stroke obtained when screwed to the respective hole. Use these 
stamped indicators as a guide for positioning the stopper.

 

Secure the stopper in place using the stopper retainer screw you removed in step 2 (Fig. 3).

(Fig. 1) PREVIEW OUT jack

(Fig. 3) Video Fader Calibrate

(Fig. 2) MENU button, [   ] and [   ] buttons, 
            and ENTER button

(Fig.1) 

Stopper

Stopper retainer screw

(Fig.3) 

Stopper retainer sc

(Fig.2) 

 

Switch off the power to the V-4.

 

Using a Phillips screwdriver, remove the screws at the four corners of the video fader (Fig. 1).

 

Turn the video fader upside-down and detach the cable connecting the V-4 to the video fader.

 

The cable is held in place by a hook on the video fader. Detach the cable from the hook (Fig. 2), then 
disconnect the connector on the video fader (Fig. 2).

 

Orient the connector as shown in the figure and insert it into the cross fader (Fig. 4).

 

Attach the cross fader using the screws you removed in step 2 (Fig. 5).

 

962a

 

202

 

Copyright ©2005 ROLAND CORPORATION. 

 

All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.

(Fig.6) 

A

A

B

B

(Fig.5) 

(Fig.4) 

(Fig.3) 

Connector

(Fig.2) 

(Fig.1) 

When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor 
in your country as shown below.

As of August 20, 2004

 (EDIROL-2)

Room 5, 9fl. No. 112 Chung Shan 
N.Road Sec.2, Taipei, TAIWAN, 
R.O.C.
TEL: (02) 2561 3339

Roland Shanghai Electronics Co.,Ltd.
5F. No.1500 Pingliang Road 
Shanghai 200090, CHINA
TEL: (021) 5580-0800

Roland Shanghai Electronics Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 Anhuaxili
Chaoyang District, Beijing 100011 
CHINA
TEL: (010) 6426-5050

Roland Shanghai Electronics Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie Yi 
Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
TEL: (020) 8736-0428

38 Campbell Avenue 
Dee Why West. NSW 2099 
AUSTRALIA 
TEL: (02) 9982 8266

Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
TEL: (2) 666 10529

Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK 
TEL: 3916 6200

Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020

Oststrasse 96, 22844 Norderstedt, 
GERMANY 
TEL: (040) 52 60090

155, New National Road
Patras 26442, GREECE
TEL: 2610 435400

Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,  HUNGARY
TEL: (23) 511011

Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666 
 

14830 Desman Rd.
La Mirada, CA 90638
U.S.A.
Tel: 1-714-521-8000
email : sales@rolandaudio.com

Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260 

Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel 
(Westerlo) BELGIUM
TEL: (014) 575811

G2 Calmount Park, Calmount 
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444

Viale delle Industrie 8, 
20020  Arese, Milano, ITALY
TEL: (02) 937-78300

Lilleakerveien 2 Postboks 95 
Lilleaker N-0216 Oslo 
NORWAY
TEL: 2273 0074
  

UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19

Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60

Piata Libertatii 1,
535500 Gheorgheni, ROMANIA
TEL: (266) 364 609

3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA 
TEL: (095) 169 5043  

Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 308 10 00

Danvik Center 28, 2 tr. 
S-131 30 Nacka SWEDEN 
TEL: (0)8 702 00 20 

Landstrasse 5, Postfach,
CH-4452 Itingen, 
SWITZERLAND
TEL: (061) 927-8383 

Mira Str. 19/108
P.O. Box 180 
295400 Munkachevo, UKRAINE
TEL: (03131) 414-40

Atlantic Close, Swansea 
Enterprise Park, SWANSEA
SA7 9FJ, 
UNITED KINGDOM
TEL: (01792) 702701

425 Sequoia Drive, Suite 114
Bellingham, WA 98226
U. S. A.
TEL: (360) 594-4273
FAX: (360) 594-4271
http://www.edirol.com/ 
  

Studio 3.4 114 Power Road 
London W4 5PY
U. K.
TEL: +44 (0)20 8747 5949
FAX:+44 (0)20 8747 5948
http://www.edirol.com/europe

Deutschland
TEL: 0700 33 47 65 20
France
TEL: 0810 000 371
Italia
TEL: 02 93778329
  

 

001

 

•

Before using this unit, make sure to read the instruc-
tions below, and the Owner’s Manual.

 

.....................................................................................................................................................................................................................................

 

002a

 

•

Do not open or perform any internal modifications on 
the unit.

 

.....................................................................................................................................................................................................................................

 

002 ex

 

•

Do not open or perform any internal modifications on 
the cross fader unit. 

 

.....................................................................................................................................................................................................................................

 

003

 

•

Do not attempt to repair the unit, or replace parts 
within it (except when this manual provides specific 
instructions directing you to do so). Refer all servicing 
to your retailer, the nearest Roland Service Center, or 
an authorized Roland distributor, as listed on the 
“Information” page.

 

.....................................................................................................................................................................................................................................

 

014

 

•

Protect the unit from strong impact.
(Do not drop it!)

 

.....................................................................................................................................................................................................................................

 

022c

 

•

Before installing the cross fader unit, you must first 
always turn off the V-4 and unplug its power cord.

 

004

 

•

Never use or store the unit in places that are:

 

•

Subject to temperature extremes (e.g., direct sunlight in an 
enclosed vehicle, near a heating duct, on top of heat-gener-
ating equipment); or are

•

Damp (e.g., baths, washrooms, on wet floors); or are

•

Humid; or are

•

Exposed to rain; or are

•

Dusty; or are

•

Subject to high levels of vibration.

 

.....................................................................................................................................................................................................................................

 

011

 

•

Do not allow any objects (e.g., flammable material, 
coins, pins); or liquids of any kind (water, soft drinks, 
etc.) to penetrate the unit.

 

.....................................................................................................................................................................................................................................

 

013

 

•

In households with small children, an adult should 
provide supervision until the child is capable of 
following all the rules essential for the safe operation of 
the unit.

 

106

 

•

Never climb on top of, nor place heavy objects on the 
unit.

 

.....................................................................................................................................................................................................................................

 

118a

 

•

Should you remove screw, keep them in a safe place 
out of children’s reach, so there is no chance of them 
being swallowed accidentally.

 

105b

 

•

If the unit could become a hazard if it moves, all caster 
wheels should be removed once the unit has been 
placed at the place of installation, or has been loaded 
onto a vehicle.

 

291a

 

•

 

354a

 

•

Do not expose the unit to direct sunlight, place it near devices 
that radiate heat, leave it inside an enclosed vehicle, or 
otherwise subject it to temperature extremes. Excessive heat 
can deform or discolor the unit..

 

355b

 

•

When moved from one location to another where the temper-
ature and/or humidity is very different, water droplets 
(condensation) may form inside the unit. Damage or 
malfunction may result if you attempt to use the unit in this 
condition. Therefore, before using the unit, you must allow it 
to stand for several hours, until the condensation has 
completely evaporated.

 

401a

 

•

For everyday cleaning wipe the unit with a soft, dry cloth or 
one that has been slightly dampened with water. To remove 
stubborn dirt, use a cloth impregnated with a mild, non-
abrasive detergent. Afterwards, be sure to wipe the unit 
thoroughly with a soft, dry cloth.

 

402

 

•

Never use benzine, thinners, alcohol or solvents of any kind, 
to avoid the possibility of discoloration and/or deformation.

 

added

 

•

The subsequent performance of the unit cannot be assured 
after the user has subjected the cross fader to any form of 
disassembly or modification.

 

553

 

•

Use a reasonable amount of care when using the unit's sliders 
and other controls. Rough handling can lead to malfunctions.

 

556

 

•

When connecting or disconnecting any cable, grasp the 
connector itself---never pull on the cable. That way, you will 
avoid causing shorts or damage to the cable's internal 
elements.

 

559c added

 

•

Dispose of the packing carton and padding for this device in 
accordance with your local standards for sorting refuse.

 

added

 

•

The cross fader is a consumable item. Replacement is possible 
only in the event of initial failure due to a manufacturing 
defect.

 

added

 

•

Exercise caution to prevent injury to the hands around the 
openings through which installations are performed, and on 
the edges of circuit boards.

Used for instructions intended to alert 
the user to the risk of injury or material 
damage should the unit be used 
improperly. 

* Material damage refers to damage or 

other adverse effects caused with 
respect to the home and all its 
furnishings, as well to domestic 
animals or pets. 

Used for instructions intended to alert 
the user to the risk of death or severe 
injury should the unit be used 
improperly. 

The 

●

  symbol alerts the user to things that must be 

carried out. The specific thing that must be done is 
indicated by the design contained within the circle. In 
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet. 

The      symbol alerts the user to important instructions 
or warnings.The specific meaning of the symbol is 
determined by the design contained within the 
triangle. In the case of the symbol at left, it is used for 
general cautions, warnings, or alerts to danger. 

The       symbol alerts the user to items that must never 
be carried out (are forbidden). The specific thing that 
must not be done is indicated by the design contained 
within the circle. In the case of the symbol at left, it 
means that the unit must never be disassembled. 

 

Before using this unit, carefully read the sections entitled: ‘’USING THE UNIT SAFELY’’ and ‘’IMPORTANT NOTES’’ .
These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel
assured that you have gained a good grasp of every feature provided by your new unit, Owner’s Manual should be read
in its entirety. The manual should be saved and kept on hand as a convenient reference.

 

03901734          

 

 

 

’05-1-1N

V-4CF_je.book 1 ページ ２００５年１月１１日　火曜日　午後３時２０分