Листовка для RCA MAF10BK

Follow these precautions to ensure safe installation and 

mounting of your flat panel TV.

  Be sure you have purchased the correct wall mount  

for your TV. Recheck the size and weight constraints.

  Gather all necessary tools before you begin installation. 

You will need a #3 bit Phillips screwdriver, electric 

drill, drill bit (included), level (integrated level on 

product), stud finder, and hammer (for brick and 

concrete installations).

  It is essential for the wall mount plate to be attached 

to wall studs. (Use a stud finder.)

  Use the included hardware for mounting purposes. 

This hardware has been provided to ensure a safe and 

secure mount.

  Hire a licensed electrician to relocate an electrical 

outlet, if needed.

  Be sure to purchase wires long enough to connect 

the TV to the audio and video components in your 

installation.

  We recommend you hire a professional installer,  

Keep your sales receipt to obtain warranty parts and 

service and for proof of purchase. Attach it here and record 

the model number. This number is located on the product.

Model No. __________________________________________

Purchase Date: ______________________________________

Dealer/Address/Phone  ______________________________

Thank you for choosing the RCA MAF10BK Universal 

Flat Panel TV Wall Mount. This mount can be used for 

all major brands of 13" - 27" flat panel TVs, 55 lbs (25 kg) 

or under. Before attempting to mount your television set, 

please remove all parts from this package and read the 

installation instructions carefully.

Before beginning the installation process, verify that you 

have all the necessary tools on hand. The following tools 

are required for proper installation:

  #3 bit Phillips screwdriver
  Stud finder
  Electric drill
  Drill bit (included)
  5/16" (8mm) masonry drill bit for concrete/ 

      brick installation

  Level (integrated level on product)
  Allen Wrench (included)
  Hammer (for concrete installations)

Package Contents
Make sure all the hardware has been included with  

your mount.

  (1) Drill Bit
  (3) 1-7/8" Drywall Screws
  (3) Concrete Anchors
  (1) Allen Wrench
  (4) M4x12mm Bolts
  (4) M4x30mm Bolts
  (4) 1/2" Spacers
  (1) Phillips-Head Driver

  Use a stud finder to locate a wood stud where you want 

to install the mount.

It is required that the wall mount plate be 

attached to wall studs.

  Locate center of stud. 

  Place the wall mount plate against the wall, with the 

cord management channel towards the bottom. Level it 

using the bubble guide. Mark the locations on the wall 

where the mount is to be installed.

  Drill holes at each marked location using the enclosed 

wood drill bit.

  Secure the wall mount plate to the wall, using one 

drywall screw, but do not completely tighten it yet.

.  Using the integrated bubble level, carefully adjust the 

wall mount plate until it is level.

  Insert the remaining screws and tighten all three 

screws completely.

  Place the wall mount plate against the wall with the 

cord management channel towards the bottom.

  Using the integrated bubble level, mark off the position 

of the holes that will be used for securing the mount.

  Place the wall mount plate aside.

  Using an electric drill and a 5/16" (8mm) masonry bit, 

drill holes in the marked locations.

  Remove any excess dust from the holes.

  Insert a concrete anchor into each hole. If necessary,  

use a hammer to lightly tap each anchor into place so 

they are flush with the wall.

  Once both anchors are in place, place the wall mount 

plate back into position.

  Attach the wall mount plate, using the drywall screws 

provided.

  Make sure all screws are tightened and secure.

  Unplug your flat panel TV before starting this step of 

the installation.

 NEVER lay the TV face down as this 

may cause damage to the viewing surface.

  Before attaching the TV mount plate to the TV, 

determine which hardware to use. Examine the back of 

your TV. If the back is flat, use the M4x12mm bolts. If 

your TV has a recessed back, use the longer M4x30mm 

bolts and 1/2" spacers.

  After you have determined which bolts to use, attach 

the TV mount plate to the back of your TV.

Be careful not to over-tighten the bolts.

  To complete the installation, slide the TV mount plate 

with your TV attached into the wall mount plate.

  The retainer clip on the top of the wall mount plate 

should click, indicating that the mount is secure.

  To remove the TV, push in on the clip and slide the TV 

mount plate up.

Model: 

MAF10BK 

 

Two-piece, low-profile design

Description: 

RCA Universal Flat Panel TV  

 

Wall Mount

TV Size Range: 

13" – 27"

Maximum Load: 

55 lbs. (25kg)

Minimum Profile: 

1.1" (2.8 cm)

VESA Compliant: 

75/100

Integrated Bubble Level
Cord Management

Audiovox Electronics Corporation (the “Company”) warrants to you the 

original retail purchaser of this product that should it, under normal use 

and conditions, be proven defective in material or workmanship during 

its lifetime while you own it, such defect(s) will be repaired or replaced (at 

the Company’s option) without charge for parts and repair labor.

To obtain repair or replacement within the terms of this Warranty, the 

product is to be delivered with proof of warranty coverage (e.g. dated bill 

of sale), specification of defect(s), transportation prepaid, to the Company 

at the address shown below. Do not return this product to the Retailer.

This  Warranty  does  not  cover  product  purchased,  serviced  or  used 

outside the United States or Canada.

This Warranty is not transferable and does not extend to costs incurred for 

installation, removal or reinstallation of the product. This Warranty does 

not apply if in the Company’s opinion, the product has been damaged 

through alteration, improper installation, mishandling, misuse, neglect, 

or accident.

THE  EXTENT  OF  THE  COMPANY’S  LIABILITY  UNDER  THIS 

WARRANTY  IS  LIMITED  TO  THE  REPAIR  OR  REPLACEMENT 

PROVIDED  ABOVE  AND,  IN  NO  EVENT,  SHALL  THE  COMPANY’S 

LIABILITY  EXCEED  THE  PURCHASE  PRICE  PAID  BY  PURCHASER 

FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY 

IMPLIED  WARRANTIES,  INCLUDING  ANY  IMPLIED  WARRANTY 

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE 

SHALL BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE 

SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR 

INCIDENTAL DAMAGES WHATSOEVER. No person or representative is 

authorized to assume for the Company any liability other than expressed 

herein in connection with the sale of this product.

Some states/provinces do not allow limitations on how long an implied 

warranty lasts or the exclusion or limitation of incidental or consequential 

damage so the above limitations or exclusions may not apply to you. This 

Warranty  gives  you  specific  legal  rights  and  you  may  also  have  other 

rights which vary from state/province to state/province.

U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,  

Hauppauge, New York  11788

CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, 

Unit 3, Door 16, Mississauga, Ontario  L5T 3A5
Trademark(s)  Registered,  Marques  Deposee,  Marcas  Registradas. 

All  other  brands  and  product  names  are  trademarks  or  registered 

trademarks of their respective owners.
© 2008 Audiovox Accessories Corporation 

111 Congressional Blvd., Suite 350 

Carmel, IN 46032