Справочник Пользователя для PASCO Specialty & Mfg. AC/DC Electronics Laboratory EM-8656
105
012-05892A
AC/DC Electronics Laboratory
®
➄
Connect one five inch wire lead from the component spring next to the emitter terminal of the
transistor to the component spring at the top left corner of the component area of the AC/DC lab
board.
transistor to the component spring at the top left corner of the component area of the AC/DC lab
board.
➅
Connect one 1 k
Ω
resistor from the component spring at the top left corner of the component
area and the component spring directly below.
➆
Connect one five inch wire lead from the component spring next to the collector terminal of the
transistor to the component spring to the right and slightly below.
transistor to the component spring to the right and slightly below.
➇
Connect one 1 k
Ω
resistor from the component spring at the end of the wire lead from the
collector terminal, to the component spring below and slightly to the right of the component
spring at the end of the wire lead from the collector terminal.
spring at the end of the wire lead from the collector terminal.
➈
Connect one 1 k
Ω
resistor from the component sprint to the right of the top banana jack, to the
component spring directly to the left of the first component spring.
➉
Connect a red banana plug patch cord from the positive (+) terminal of the DC power supply to
the top banana jack on the AC/DC lab board.
the top banana jack on the AC/DC lab board.
11
Connect a black banana plug patch cord from the negative (-) terminal of the DC power supply
to the bottom banana jack on the AC/DC lab board.
to the bottom banana jack on the AC/DC lab board.
12
Connect the ten inch wire lead from the component spring next to the bottom banana jack to the
component spring at the bottom end of the 1 k
component spring at the bottom end of the 1 k
Ω
resistor that is connected to the emitter terminal
of the transistor.
13
Find the component spring at the end of the wire lead that is connected to the component spring
at the base terminal of the transistor. Connect the 10 k
at the base terminal of the transistor. Connect the 10 k
Ω
resistor from the component spring at
the end of the wire lead to a component spring at the bottom left corner of the board.
➤ NOTE: You can connect one end of the 10 k
Ω
resistor to the same component spring that
holds one end of the ten inch wire lead.
14
Return to the component spring that is at the end of the wire lead connected to the base terminal
of the transistor. Connect one 22 k
of the transistor. Connect one 22 k
Ω
resistor from the component spring at the end of the wire
lead to the component spring that is to the right and below (at the edge of the AC/DC lab board).
15
Connect one five inch wire lead from the component spring at the end of the 22 k
Ω
resistor to a
component spring next to the top banana jack.
16
Put an alligator clip on one end of a red banana plug patch cord. Connect the alligator clip to the
wire at the end of the 1
wire at the end of the 1
µ
F capacitor. Connect the other end of the patch cord to the positive (+)
terminal of the Power Amplifier
17
Connect a black banana plug patch cord from the negative (-) terminal of the Power Amplifier to
the negative terminal of the DC power supply.
the negative terminal of the DC power supply.
18
Put alligator clips on the banana plugs of the Voltage Sensor. Connect the alligator clip of the
black wire of the Voltage Sensor to the component spring next to the bottom banana jack at the
lower right corner of the AC/DC board.
black wire of the Voltage Sensor to the component spring next to the bottom banana jack at the
lower right corner of the AC/DC board.
19
Twist the wire from the negative end of the 10
µ
F capacitor together with the wire at one end of
one 22 k
Ω
resistor.