Справочник Пользователя для PASCO Specialty & Mfg. AC/DC Electronics Laboratory EM-8656
1
012-05892A
AC/DC Electronics Laboratory
®
Introduction
The EM-8656 AC/DC Electronics Laboratory is designed
for both DC and AC electricity experiments. The circuit
board can be powered by batteries for DC experiments or
it can be powered by a computer equipped with a Power
Amplifier for AC experiments. The AC experiments
could also be performed without a Power Amplifier if a
function generator is available.
for both DC and AC electricity experiments. The circuit
board can be powered by batteries for DC experiments or
it can be powered by a computer equipped with a Power
Amplifier for AC experiments. The AC experiments
could also be performed without a Power Amplifier if a
function generator is available.
The first ten experiments in this manual are DC experi-
ments using battery power and multimeters rather than
using a computer. The rest of the experiments use a
computer (MAC or PC) with a Power Amplifier. The
software used is Science Workshop™.
ments using battery power and multimeters rather than
using a computer. The rest of the experiments use a
computer (MAC or PC) with a Power Amplifier. The
software used is Science Workshop™.
Equipment
The PASCO Model EM-8656 AC/DC Electronics
Laboratory includes the following materials:
Laboratory includes the following materials:
• Circuits Experiment Board
• Storage Case
• Component Bag
• Experiment Manual
The Circuit Experiment Board features:
(2) Battery Holders, D-cell, (Batteries not included)
(3) Light Sockets
(3) #14 Light Bulbs – 2.5 V, 0.3 A*
(1) Transistor Socket
(1) Coil (Renco RL-1238-8200)
(1) Resistor–– 3.3
Ω
, 2W, 5%
(36) Component springs
(2) Banana Jacks (for power amplifier)
(1) Potentiometer–– 25
Ω
, 2W
(1) Pushbutton switch
The Storage Case features:
(1) Cable clamp and 1/2" iron core
The Component Bag includes:
Resistors, 5%
(1) 33
Ω
–– 5 watt
(2) 10
Ω
–– 1 watt
(2) 4.7
Ω
–– 1/2 watt
(2) 100
Ω
–– 1/2 watt
(4) 330
Ω
–– 1/2 watt
(2) 560
Ω
–– 1/2 watt
(4) 1 K
Ω
–– 1/2 watt
(2) 10 K
Ω
–– 1/2 watt
(1) 100 K
Ω
–– 1/2 watt
(1) 220
ΚΩ
–– 1/2 watt
(2) 22 K
Ω
–– 1/4 watt
(1) 3.3 K
Ω
–– 1/4 watt
Capacitors
(1) 1
µ
F–– 35 volts
(2) 10
µ
F–– 25 volts
(1) 47
µ
F–– 50 volts
(1) 470
µ
F–– 16 volts
(1) 100
µ
F–– 16 volts
(1) 330
µ
F–– 16 volts
(6) Diodes 1N-4007
(2) Transistors 2N-3904
(1 ea) LED red, green, yellow, bicolor
Wire Leads––22 ga. (4@5" and 5 @10")
* NOTE: Due to manufacturer's tolerances,
wattage may vary by 15-30% from bulb to bulb.
wattage may vary by 15-30% from bulb to bulb.