Справочник Пользователя для Garmin Lawn Mower 1.2
1.2 L and 2.0 L Hydraulic Pump Installation Instructions
1
1.2 and 2.0 L Hydraulic Pump
Installation Instructions
To obtain the best performance and to avoid damage to your boat,
install the Garmin
®
1.2/2.0 L hydraulic pump according to the following
instructions. These instructions are a supplement to the installation
instructions provided with your Garmin autopilot.
Professional installation of the pump is highly recommended, because
Professional installation of the pump is highly recommended, because
specific knowledge of hydraulic steering componentry is required to
properly install the pump.
Read all installation instructions before proceeding with the
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation, contact
Garmin Product Support.
Registering Your Product
Help us better support you by completing your online registration today.
• Go to
• Go to
http://my.garmin.com
.
• Keep the original sales receipt, or a photocopy, in a safe place.
Contacting Garmin Product Support
Contact Garmin Product Support if you have any questions about this
product.
• In the USA, go to
• In the USA, go to
www.garmin.com/support
, or contact Garmin
USA by phone at (913) 397.8200 or (800) 800.1200.
• In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
• In Europe, go to
• In Europe, go to
www.garmin.com/support
and click Contact
Support for in-country support.
Important Safety Information
‹
waRnInG
Your are responsible for the safe and prudent operation of your
vessel. The autopilot is a tool that will enhance your capability to
operate your boat. It does not relieve you from the responsiblility of
safely operating your boat. Avoid navigational hazards and never leave
the helm unattended.
See the Important Safety and Product Information guide in the autopilot
See the Important Safety and Product Information guide in the autopilot
product box for product warnings and other important information.
‹
CautIon
Failure to install and maintain this equipment in accordance with these
instructions could result in damage or injury.
Always wear safety goggles, ear protection, and a dust mask when
Always wear safety goggles, ear protection, and a dust mask when
drilling, cutting, or sanding.
notice
This equipment should be installed by a qualified marine installer.
This equipment is only for use with Garmin autopilots.
When drilling or cutting, always check the opposite side of the surface.
This equipment is only for use with Garmin autopilots.
When drilling or cutting, always check the opposite side of the surface.
Be aware of fuel tanks, electrical cables, and hydraulic hoses.
about the 1.2/2.0 L Hydraulic Pump
The 1.2/2.0 L hydraulic pump steers your boat by interacting with the
hydraulic steering system, based on commands you enter using the
autopilot display unit. The pump is not included in the autopilot core
package box because the type of pump you use with your autopilot is
determined by the size and type of steering system on your boat.
Hardware needed
• 1.2/2.0 L pump kit (part number 010-11098-00)
• Unbalanced kit (if installing in a boat with an unbalanced steering
• Unbalanced kit (if installing in a boat with an unbalanced steering
cylinder, part number 010-11201-00)
• Hydraulic hose with machine-crimpted or field-replaceable fittings
that have a minimum rating of 1000 lbf/in
2
.
• Hydraulic fluid
• Thread sealant
• Hydraulic bleeding equipment
• Mounting screws: mounting screws are provided in the pump kit, but
• Thread sealant
• Hydraulic bleeding equipment
• Mounting screws: mounting screws are provided in the pump kit, but
if the provided screws are not appropriate for the mounting surface,
you must provide the correct types of screws.
tools needed
• Safety glasses
• Drill and drill bits
• Wrenches
• Torque wrench (if installing unbalanced kit)
• Wire cutter/strippers
• Screwdrivers: Phillips and flat
• Cable ties
• Marine sealant
• Marine corrosion inhibitor spray
• Drill and drill bits
• Wrenches
• Torque wrench (if installing unbalanced kit)
• Wire cutter/strippers
• Screwdrivers: Phillips and flat
• Cable ties
• Marine sealant
• Marine corrosion inhibitor spray
Pump Installation
Because every boat is different, care must be taken when planning the
pump installation.
1. Choose a mounting location (
1. Choose a mounting location (
).
).
3. Connect the pump to the hydraulic lines (
).
).
Choosing a Mounting Location
for connection and dimension
considerations.
2. Choose a location to install the pump, considering these guidelines:
• The pump must be located within 19 in. (0.5 m) of the ECU.
• The cables that connect the pump to the ECU cannot be
• The cables that connect the pump to the ECU cannot be
extended.
• The pump should be mounted horizontally, if possible.
• If the pump cannot be mounted pump horizontally, it must be
• If the pump cannot be mounted pump horizontally, it must be
mounted vertically with the pump head connectors facing up.
• The pump must be mounted in a location to which you can
extend the hydraulic steering lines of the boat.