Справочник Пользователя для Bosch 3540
5.
• If any part of your saw is missing, malfunctioning, has been
damaged or broken … such as the motor switch, or other
operating control, a safety device or the power cord … cease
operating immediately until the particular part is properly
repaired or replaced.
damaged or broken … such as the motor switch, or other
operating control, a safety device or the power cord … cease
operating immediately until the particular part is properly
repaired or replaced.
• NEVER place your face or body in line with the cutting tool.
• NEVER place your fingers and hands in the path of the
sawblade or other cutting tool.
sawblade or other cutting tool.
• DO NOT perform any operation “FREEHAND” — always use
the fence to position and guide the work for both rip cuts and
crosscuts.
the fence to position and guide the work for both rip cuts and
crosscuts.
• Provide adequate support to the rear and sides of the saw
table for wider or long workpieces.
table for wider or long workpieces.
• If you stall or jam the tile blade in the workpiece, turn saw
“OFF”, remove the workpiece from the tile blade, and check to
see if the tile blade is parallel to the table slots or grooves and
if the riving knife is in proper alignment with the sawblade. If
ripping at the time, check to see if rip fence is parallel with the
sawblade. Readjust as indicated.
“OFF”, remove the workpiece from the tile blade, and check to
see if the tile blade is parallel to the table slots or grooves and
if the riving knife is in proper alignment with the sawblade. If
ripping at the time, check to see if rip fence is parallel with the
sawblade. Readjust as indicated.
• DO NOT remove small pieces of cut-off material that may
become trapped inside the blade guard while the saw is
running. This could endanger your hands or cause a kick back.
Turn saw “OFF” and wait until blade stops.
become trapped inside the blade guard while the saw is
running. This could endanger your hands or cause a kick back.
Turn saw “OFF” and wait until blade stops.
KNow YoUR cUTTiNG ToolS
Dull, gummy or improperly sharpened or set cutting tools can
cause material to stick, jam, stall the saw, or kickback at the
operator. Minimize potential injury by proper cutting tool and
machine maintenance. NEVER ATTEMPT TO FREE A
STALLED SAWBLADE WITHOUT FIRST TURNING THE
SAW OFF.
Dull, gummy or improperly sharpened or set cutting tools can
cause material to stick, jam, stall the saw, or kickback at the
operator. Minimize potential injury by proper cutting tool and
machine maintenance. NEVER ATTEMPT TO FREE A
STALLED SAWBLADE WITHOUT FIRST TURNING THE
SAW OFF.
•NEVER use toothed blade on the tile saw.
•Make sure the cutting tool rotates in the same direction as the
rotation arrow on the upper guard. Also make sure the cutting
tool, arbor collars and arbor nut are installed pro p erly. Keep
the cutting tool as low as possible for the oper ation being
performed. Keep all guards in place whenever possible.
rotation arrow on the upper guard. Also make sure the cutting
tool, arbor collars and arbor nut are installed pro p erly. Keep
the cutting tool as low as possible for the oper ation being
performed. Keep all guards in place whenever possible.
• Do not use any blade or other cutting tool marked for an
operating speed less than 3600 R.P.M. Never use a cutting
tool larger in diameter than the diameter for which the saw
was designed.
operating speed less than 3600 R.P.M. Never use a cutting
tool larger in diameter than the diameter for which the saw
was designed.
Safety
“READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by BULLET (•) symbol listed
BELOW and other safety precautions, may result in serious personal injury.
BELOW and other safety precautions, may result in serious personal injury.
WARNING
!
“SaVe TheSe iNSTRUcTioNS”
SM_2610008271_12-09:tile saw 12/17/09 3:25 PM Page 5