Справочник Пользователя для Behringer LC2412

EUROLIGHT LC2412 User Manual

Exception: When the LC2412 is in preset mode (“P” shown in  the bank display), 

the faders control the same channels as the faders of the A PRESET section. 

This way, you can simul-taneously create a second preset.

(14) 

–   

(17)

  These faders are also a part of this section, but they have a double 

function. When the LC2412 is in sound to light mode (party light function), 

they control the illumination level of individual memories assigned to 

particular frequency ranges.

(18) 

The BANK display shows the storage bank to which the memories you recall 

belong. It also shows if the LC2412 is currently in preset mode (“P” diplayed). 

The display starts flashing when you switch into preset mode, and lights 

up constantly after three seconds. The preset mode is active only after the 

flashing has stopped. This prevents accidental activation of the preset mode 

as well as rough fades. 

(19) 

UP/DOWN keys. Use them to select a preset bank (0 - 9) or switch into 

preset mode (P). The control lights flash when you select a new bank while 

memories from the previous bank are still active (the fader(s) is(are) pulled 

up). Pull the fader(s) (

(13)

, 

(14) 

- 

(17)

) down to fade the memory out. When you 

pull the fader(s) up again, the memory of the new preset bank is visible on 

the stage (also see chapter 4.1.2).

(20) 

SOUND TO LIGHT key. See chapter 2.3.

(21) 

PREVIEW key. It gives you the option to preview (or modify) stored 

memories one more time before implementing them on the stage. This is 

particularly useful when you saved chases as memories and wish to 

double-check and/or modify their speed before integrating them into a 

running show. When “preview” is activated, the chases are shown on control 

LEDs exclusively.

Each fader is assigned to a FLASH key (section  

(4)

). This key is used to assign a 

specific bank position to individual presets while programming a memory.

The SOUND-TO-LIGHT controls are located in the right-hand section of the 

B MEMORY section. 
If the sound-to-light function is active, memories 9 - 12 are controlled by a music 

signal, whereby the volume of the signal dictates the illumination level of the 

memories. The music signal is divided into three frequency ranges (bass, mids, 

higs). One memory slot is assigned to each of the three frequency ranges. 

For optimal results, please put the faders to the middle position. This will let you 

bring individual settings of memories into sync with one another, should the 

levels vary from memory to memory. 

(14) (15) (16) (17)

(18)

(20)

(19)

Fig. 2.4: The SOUND-TO-LIGHT section

(14) 

The PAUSE fader is, just like the fader  

(13)

, used primarily to control the 

illumination level of memories. If the sound-to-light function is active, 

it controls a memory slot assigned to run during program breaks between 

two musical pieces.

(15) 

The BASS fader takes over the basic configuration of the illumination levels 

for the memory slot assigned to the bass portion of the frequency range.

(16) 

The MID fader is conversely assigned to the mids.

(17) 

The TREBLE fader is conversely assigned to the highs.

(18) 

and   

(19)

: Bank display and UP/DOWN keys, see chapter 2.2.

(20) 

The SOUND-TO-LIGHT key activates the sound-to-light funtion.

The music signal necessary for controlling the show can be fed into the 

ANALOG INPUT connector located at the rear of the LC2412.

(22)

(23)

Fig. 2.5: The FLASH keys

(22) 

FLASH keys. Pressing one of the FLASH keys sets the respective channel to 

the maximum illumination level set on the MAIN fader, independent from 

its own fader position. For this purpose, the CH FLASH key has to be pressed. 

The channel flash function is automatically activated in preset mode.

(23) 

Dual-function FLASH keys. Memories or chases can be stored to memory 

positions 9 - 12 (chase to memory). When a respective storage bank is 

selected, chases are indicated with yellow LEDs. Chases can also be recalled 

by using the Flash keys.

Solo
When the solo function is simultaneously active (SOLO key  

(31)

, LED lit), all other 

emitters or light elements are deactivated. Only the channel selected via the 

Flash key is still active.

2.4.1  Disabling the solo function
You have the option to exclude specific channels from the solo function, so that 

these channels remain active even when “Solo” is activated.
Disabling solo is achieved by performing the folloing programming sequence:
1.  Press UTILITY 1  

(28)

.

2.  Select the option DISABLE SOLO by using the SOFT A key  

(38)

  located below 

the display. The channel for which the solo function should be disabled 

or enabled is shown in the top left section of the display. The respective 

disabled/enabled status of the said channel is indicated to the right of the 

channel number itself.

3.  To select the channel you wish to adjust, turn the DATA wheel  

(36)

. 

The desired channel can also be selected by using the Flash key 

(for channels 13 - 24: first press the UPPER key).

4.  SOFT B  

(39)

  selects “DISABLE” and thus disables the solo function for this 

channel; SOFT A selects “ENABLE”.

5.  To exit this procedure, press the QUIT key  

(40)

, thus confirming the procedure.