Справочник Пользователя для Toshiba 48-1250 A
TOSHIBA - 46
TX Series
48 - 1250A
SP.7 Custom Acceleration Curve (Setpoint Page 7)
(Security Level: 3)
(Security Level: 3)
MENU
PAGE 7 CUSTOM
ACCELERATION CURVE
ACCELERATION CURVE
CUSTOM ACCEL CURVE
: DISABLED
: DISABLED
Range: DISABLED,
CURVE A, B or C
CURVE A, B or C
(Hit DOWN ARROW six times)
CURVE A VOLTAGE
LEVEL 1: 25%
LEVEL 1: 25%
CUSTOM CURVE A
CURVE A RAMP
TIME 1: 2 SEC
TIME 1: 2 SEC
CURVE A RAMP
TIME 2: 2 SEC.
TIME 2: 2 SEC.
CURVE A VOLTAGE
LEVEL 3: 37%
LEVEL 3: 37%
CURVE A RAMP
TIME 3: 2 SEC.
TIME 3: 2 SEC.
CURVE A VOLTAGE
LEVEL 2: 30%
LEVEL 2: 30%
CURVE A VOLTAGE
LEVEL 4: 45%
LEVEL 4: 45%
CURVE A VOLTAGE
LEVEL 5: 55%
LEVEL 5: 55%
CURVE A RAMP
TIME 5: 2 SEC.
TIME 5: 2 SEC.
CURVE A VOLTAGE
LEVEL 6: 67%
LEVEL 6: 67%
CURVE A RAMP
TIME 4: 2 SEC.
TIME 4: 2 SEC.
CURVE A VOLTAGE
LEVEL 7: 82%
LEVEL 7: 82%
CURVE A RAMP
TIME 7: 2 SEC.
TIME 7: 2 SEC.
CURVE A RAMP
TIME 6: 2 SEC.
TIME 6: 2 SEC.
Range: 0 - 100%
Increments of 1
Increments of 1
Range: 1 - 60 SEC
Increments of 1
Increments of 1
Range: 0 - 100%
Increments of 1
Increments of 1
Range: 1 - 60 SEC
Increments of 1
Increments of 1
Range: 0 - 100%
Increments of 1
Increments of 1
Range: 1 - 60 SEC
Increments of 1
Increments of 1
Range: 0 - 100%
Increments of 1
Increments of 1
Range: 1 - 60 SEC
Increments of 1
Increments of 1
Range: 0 - 100%
Increments of 1
Increments of 1
Range: 1 - 60 SEC
Increments of 1
Increments of 1
Range: 0 - 100%
Increments of 1
Increments of 1
Range: 1 - 60 SEC
Increments of 1
Increments of 1
Range: 0 - 100%
Increments of 1
Increments of 1
Range: 1 - 60 SEC
Increments of 1
Increments of 1
SP7.1
Setpoint Page 7 allows the user to custom
design the acceleration curve (start curve) to the
specific application. The user can custom
design up to three different curves in the TX.
Only one curve can be active (enabled) at a
time. Each of the three curves allow for eight
voltage plotting points, with corresponding ramp
times and a current limit setting.
Note: Each successive voltage level must be
programmed to a voltage level equal to or greater
than the previous level. All eight levels of
voltages must be programmed and the eighth
level has been preset at 100%.
design the acceleration curve (start curve) to the
specific application. The user can custom
design up to three different curves in the TX.
Only one curve can be active (enabled) at a
time. Each of the three curves allow for eight
voltage plotting points, with corresponding ramp
times and a current limit setting.
Note: Each successive voltage level must be
programmed to a voltage level equal to or greater
than the previous level. All eight levels of
voltages must be programmed and the eighth
level has been preset at 100%.
• If Custom Accel Curve has been set to curve A, B
or C on this page, the TX will override the Start
Control Mode selected in Setpoint Page 2, (even
if Start Control Mode in Setpoint Page 2 has not
been set to Custom Accel Curve).
Note: Setpoint Page 7 has a security level 3
requirement.
Control Mode selected in Setpoint Page 2, (even
if Start Control Mode in Setpoint Page 2 has not
been set to Custom Accel Curve).
Note: Setpoint Page 7 has a security level 3
requirement.