Справочник Пользователя для QVC TCE5850

Read all the sections of this booklet and follow all the instructions carefully.

1. Before using your Convertible 

Hand/Stand Mixer for the first time, 
wash the beaters, dough hooks, 
bowls and spatula in warm, sudsy 
water. Rinse and dry thoroughly. Use 
a damp cloth to wash over the mixer 
base and the hand mixer. Dry with a 
soft cloth.  NEVER immerse the base 
stand or the hand mixer in water or 
any other liquids.

2. Before assembling your Convertible 

Hand/Stand Mixer, make sure that the 
power cord is unplugged from the 
electrical outlet and that both the 
speed control and the base speed 
control dial are in the “OFF” position.

1. Ensure that the hand mixer is not 

plugged in to an electrical outlet 
and that the speed control switch 
is on the “0” (off) position.

2. Insert the beaters into the sockets 

on the under side of the hand 
mixer and twist counter clockwise 
until the beater is firmly fitted into 
the socket.

3. To release the beaters from the 

unit, press on the beater eject 
button on the front of the unit and 
they will pop out. (Fig. 1)

To avoid injury when 

inserting or removing beaters or 

dough hooks, always set the speed 
selector on “0” and unplug the appliance.

1. Ensure that the hand mixer is not 

plugged in to an electrical outlet 
and that the speed control switch 
is on the “0” (off) position.

2. The dough hooks have a set 

method of fitting into the hand 
mixer because they are not 
identical. One has a grommet and 
the other does not. (Fig. 2)

Fig. 1

3. Looking at the under side of the 

hand mixer, you will see that one 
of the sockets has a red dot over 
it. (Fig. 3) Insert the dough hook 
with the grommet into this socket. 

4. Then insert the other dough hook 

into the other socket. Push both 
dough hooks in until you hear a 
click confirming that they are 
securely in place. 

5. To release the dough hooks from 

the unit, press on the beater eject 
button on the front of the unit and 
they will pop out. (Fig. 1)

: Ensure that the beaters or 

dough hooks are fully inserted into 
the correct sockets or your mixing 
results may be affected.

Fig. 2

Fig. 3

1. Press the tilt button, located on the 

top of the support pivot . While the 
button is depressed, ease the support 
pivot back. (Fig. 4) 

To avoid injury when 

assembling the hand mixer to the 

stand, always set the speed selector on 
“0” and unplug the appliance.

Fig. 4

The support pivot will lock into this 
raised position until it is released by 
pressing the tilt button again.

2. To connect the hand mixer to the 

support pivot, locate the two retaining 
prongs on the support pivot into the 
two rectangular holes in the heel of 
the hand mixer. (Fig. 5) When the 
hand mixer is seated on the support 
pivot, press down on the hand mixer 
to click it into place and lock the hand 
mixer and the support pivot together.

Fig. 5

NOTE: Ensure that the two retaining 
prongs on the support pivot are fully 
connected into the hand mixer.

3. While the hand mixer is still in the 

raised position, insert either the 
beaters or the dough hooks.

4. To lower the hand mixer, press and 

hold the tilt button with one hand 
while holding the hand mixer with the 
other hand and slowly lower the hand 
mixer down. (Fig. 6)

Fig. 6

5. To remove the hand mixer from the 

pivot support, first raise the mixer by 
pressing the tilt button and raise the 
mixer up. (Fig. 7) the mixer will lock 
into the raised position.

6. Then press the mixer release button 

which is located on the under side of 
the pivot support with one hand and 
with the other lift the hand mixer by 
the handle upwards and away from 
the support pivot. (Fig. 8)

Fig. 7

Fig. 8