Инструкции Пользователя для BMW 2005 745Li Sedan
205
Grasp the handle in the upper panel and
fold it down.
Undo the wingnut and remove the jack.
After use, screw the jack all the way
back down and snap the handle back
into place.
fold it down.
Undo the wingnut and remove the jack.
After use, screw the jack all the way
back down and snap the handle back
into place.
Spare tire
1.
Unscrew the wing nut 1
2.
Remove the disc 2 to the side
3.
Completely unscrew the threaded rod 3
4.
Remove the spare tire.
Preparing wheel change
1.
Read carefully and comply with the
safety precautions on page
safety precautions on page
2.
Secure the vehicle to prevent it from
rolling:
Place the wheel chock against the rear
surface of the front tire on the side
opposite the side being raised. If the
vehicle is parked on a downward slope,
place the wheel chock securely in front
of the tire. On a steep grade, also
secure the vehicle against rolling
rolling:
Place the wheel chock against the rear
surface of the front tire on the side
opposite the side being raised. If the
vehicle is parked on a downward slope,
place the wheel chock securely in front
of the tire. On a steep grade, also
secure the vehicle against rolling
3.
Loosen the lug bolts 1/2 a turn.
Lifting vehicle
1.
Position the jack at the jacking point
closes to the wheel so that the entire
jack base makes contact vertically
under the jacking point
closes to the wheel so that the entire
jack base makes contact vertically
under the jacking point
The vehicle jack is designed for
changing wheels only. Do not
changing wheels only. Do not
attempt to raise another vehicle model
with it or to raise any load of any kind.
To do so could cause accidents and
personal injury.
with it or to raise any load of any kind.
To do so could cause accidents and
personal injury.
<
2.
Guide the jack head into the rectangular
recess of the jacking point when crank-
ing up the jack, refer to section of illus-
tration
recess of the jacking point when crank-
ing up the jack, refer to section of illus-
tration
3.
Jack the vehicle up until the wheel you
are changing is raised from the ground.
are changing is raised from the ground.
Mounting a wheel
1.
Unscrew the lug bolts and remove the
wheel
wheel
2.
Remove accumulations of mud or dirt
from the mounting surfaces of the
wheel and hub. Clean the lug bolts
from the mounting surfaces of the
wheel and hub. Clean the lug bolts
3.
Position the wheel or spare tire on the
hub and screw in at least two bolts
diagonally.
When you mount wheels other than
Genuine BMW light-alloy wheels, differ-
ent lug bolts may also be required
hub and screw in at least two bolts
diagonally.
When you mount wheels other than
Genuine BMW light-alloy wheels, differ-
ent lug bolts may also be required
4.
Screw in the remaining lug bolts.
Tighten all the bolts securely in a diag-
onal pattern
Tighten all the bolts securely in a diag-
onal pattern
5.
Lower the vehicle and remove the jack
from beneath the vehicle.
from beneath the vehicle.
Following installation
1.
Tighten the lug bolts in a diagonal pat-
tern
tern
To ensure safety, always have the
lug bolts checked with a cali-
lug bolts checked with a cali-
brated torque wrench as soon as possi-
ble to ensure that they are tightened to
the specified torque. The tightening
torque is 140 Nm.
ble to ensure that they are tightened to
the specified torque. The tightening
torque is 140 Nm.
<
2.
Reverse the removal sequence when
storing the wheel and tools in the vehi-
cle
storing the wheel and tools in the vehi-
cle
Online Edition for Part-No. 01 41 0 159 154 - © 09/04 BMW AG