Инструкции По Обслуживанию для Summit TDC112C
Service menu
Turn/
Push
Push
Display
Comments/instructions
SP: xxxx
Date the software was programmed (Year_Week)
T
R
A
C
K
IN
G
D
A
TA
CM: xxxx
Date of manufacture of the control unit (Year_Week)
SV: xxxxxxxxx
Software version number
NCP0: xxxxxxxxx
Total number of cycles run
NCP1: xxxxxxxxx
Number of cycles run for Programme 1
NCP2: xxxxxxxxx
Number of cycles run for Programme 2
NCP3: xxxxxxxxx
Number of cycles run for Programme 3
NCP4: xxxxxxxxx
Number of cycles run for Programme 4
NCP5: xxxxxxxxx
Number of cycles run for Programme 5
NCP6: xxxxxxxxx
Number of cycles run for Programme 6
NCP7: xxxxxxxxx
Number of cycles run for Programme 7
NCP8: xxxxxxxxx
Number of cycles run for Programme 8
NCP9: xxxxxxxxx
Number of cycles run for Programme 9
NCP10: xxxxxxxxx
Number of cycles run for Programme 10
NCP11: xxxxxxxxx
Number of cycles run for Programme 11
Auto extratorrt
Auto skåptorrt
Tidsprogram
Auto normaltorrt
Auto stryktorrt
Luftningsprogram
Auto stryktorrt
Luftningsprogram
T 7 5 3 C B U T T E R F L Y D R Y I N G
”Fault No. of cycles(1)”
Last three faults and number of cycles (when the fault occurred) shown. A total reset
deletes the fault indications from the system. If the same fault recurs at different times,
this is shown, but only once in the list.
FA
IL
U
R
E
R
EE
D
D
O
U
T
”Fault No. of cycles (2)”
”Fault No. of cycles (3)”
Auto extratorrt
Auto skåptorrt
Tidsprogram
Auto normaltorrt
Auto stryktorrt
Luftningsprogram
Auto stryktorrt
Luftningsprogram
T 7 5 3 C B U T T E R F L Y D R Y I N G
Opening the service menu
Auto extratorrt
Auto skåptorrt
Tidsprogram
Auto normaltorrt
Auto stryktorrt
Luftningsprogram
Auto stryktorrt
Luftningsprogram
T 7 5 3 C B U T T E R F L Y D R Y I N G
+
Auto extratorrt
Auto skåptorrt
Tidsprogram
Auto normaltorrt
Auto stryktorrt
Luftningsprogram
Auto stryktorrt
Luftningsprogram
T 7 5 3 C B U T T E R F L Y D R Y I N G
Check that the machine is switched off. Otherwise switch off the main power by pressing the main power switch
(S1).
Press and hold the Start button (S2) while turning on the main power with the main power switch (S1).
(S1).
Press and hold the Start button (S2) while turning on the main power with the main power switch (S1).
Auto extratorrt
Auto skåptorrt
Tidsprogram
Auto normaltorrt
Auto stryktorrt
Luftningsprogram
Auto stryktorrt
Luftningsprogram
T 7 5 3 C B U T T E R F L Y D R Y I N G
Press the Start button (S2) 5 times within 5 seconds. The service menu is now activated, as seen in the display
window. The service menu can be closed by turning off the power with the main power switch (S1).
window. The service menu can be closed by turning off the power with the main power switch (S1).
Auto extratorrt
Auto skåptorrt
Tidsprogram
Auto normaltorrt
Auto stryktorrt
Luftningsprogram
Auto stryktorrt
Luftningsprogram
T 7 5 3 C B U T T E R F L Y D R Y I N G
Press the Stop button (S3) to navigate the menu system step by step.
Auto extratorrt
Auto skåptorrt
Tidsprogram
Auto normaltorrt
Auto stryktorrt
Luftningsprogram
Auto stryktorrt
Luftningsprogram
T 7 5 3 C B U T T E R F L Y D R Y I N G
Turn the programme selector (J1) to make selections from the menus.
Confirm the selection and continue to the next menu by pressing the Stop button (S3).
Confirm the selection and continue to the next menu by pressing the Stop button (S3).
Auto extratorrt
Auto skåptorrt
Tidsprogram
Auto normaltorrt
Auto stryktorrt
Luftningsprogram
Auto stryktorrt
Luftningsprogram
T 7 5 3 C B U T T E R F L Y D R Y I N G
Press the Start button (S2) to confirm the settings and exit the service menu.
x 5
Panel key: S = Push button, J = Knob
S3
J1
DISPLAY
S2
S1
Service Manual TD70.C
30