Техническое Описание для Amana PTC094G35AXXX
SS-DPTAC www.amana-ptac.com
7
6
www.amana-ptac.com SS-DPTAC
P
roduCT
s
PeCifiCATions
P
roduCT
s
PeCifiCATions
Furnish and install air-cooled through-the-wall package terminal air conditioners amd heat pumps (assembled in the USA).
Units are rated in accordance with the ARI (Air Conditioning & Refrigeration Institute) Standards 310/380-93, CSA (Canadian
Standards Association) EEV certification programs and listed by U. L. (Underwriters Laboratories).
Units are rated in accordance with the ARI (Air Conditioning & Refrigeration Institute) Standards 310/380-93, CSA (Canadian
Standards Association) EEV certification programs and listed by U. L. (Underwriters Laboratories).
r
ATings
Each unit must meet the following specifications:
ARI rating of _________BTUH cooling (and _________ BTUH
reverse cycle heating with a COP of _________ at 47° F O.D.)
Electric resistance heat of _________ BTUH. Total Amp draw
must be of ________ and _________ Watts at _________ volts.
The unit must remove a minimum of _________ pints of
moisture per hour when operated at rating conditions. The EER
must be a minimum of _________ EER.
ARI rating of _________BTUH cooling (and _________ BTUH
reverse cycle heating with a COP of _________ at 47° F O.D.)
Electric resistance heat of _________ BTUH. Total Amp draw
must be of ________ and _________ Watts at _________ volts.
The unit must remove a minimum of _________ pints of
moisture per hour when operated at rating conditions. The EER
must be a minimum of _________ EER.
u
niT
C
HAssis
Each unit must be slide out design shipped with room cabinet
front installed. Unit chassis must have the ability to be installed
with 0 clearance from finished floor. An electrical power cord
must be included with chassis and installed by the manufacturer
to assure proper NEMA 6 or 7 configuration and UL-approved
length. Units less than 250 volts must also have a LCDI power cord.
Unit must be tested for conformance to ASTME water infiltration
specification ASTME 331-86, which ensures no water infiltration
when tested at 8" rain per hour at 63 mph wind for 15 minutes.
front installed. Unit chassis must have the ability to be installed
with 0 clearance from finished floor. An electrical power cord
must be included with chassis and installed by the manufacturer
to assure proper NEMA 6 or 7 configuration and UL-approved
length. Units less than 250 volts must also have a LCDI power cord.
Unit must be tested for conformance to ASTME water infiltration
specification ASTME 331-86, which ensures no water infiltration
when tested at 8" rain per hour at 63 mph wind for 15 minutes.
r
oom
C
AbineT
The monochromatic front of the room cabinet must be able to
be field-secured to chassis to inhibit tampering. Filter must be
accessible without removing room front. Cabinet depth must
not exceed 7⅝” to minimize unit’s impact on room space.
be field-secured to chassis to inhibit tampering. Filter must be
accessible without removing room front. Cabinet depth must
not exceed 7⅝” to minimize unit’s impact on room space.
C
oils
Unit’s coils must have rifled copper tubing expanded into
rippled-edge louvered aluminum fins. Exterior coil must be of
a two-row bent coil design with removable shroud top to allow
easy-access for cleaning of the exterior coil.
rippled-edge louvered aluminum fins. Exterior coil must be of
a two-row bent coil design with removable shroud top to allow
easy-access for cleaning of the exterior coil.
H
eAT
P
umPs
Each unit must include a change-over thermistor that senses an
outside ambient switch-over temperature as low as 24°F, lock-
open refrigerant reversing valve during heat pump operation,
temperature-activated defrost drain and automatic emergency
heat operation to override the heat pump’s change-over
thermostat and bring on electric resistance heaters in the event
of a sealed system failure. Unit must not operate compressor
and electric heaters simultaneously.
outside ambient switch-over temperature as low as 24°F, lock-
open refrigerant reversing valve during heat pump operation,
temperature-activated defrost drain and automatic emergency
heat operation to override the heat pump’s change-over
thermostat and bring on electric resistance heaters in the event
of a sealed system failure. Unit must not operate compressor
and electric heaters simultaneously.
C
omPressor
The compressor must be hermetically sealed, internally isolated,
rotary-type and permanently mounted on rubber isolators. No
removal or adjustment of compressor hold-down bolts is to be
required during installation.
rotary-type and permanently mounted on rubber isolators. No
removal or adjustment of compressor hold-down bolts is to be
required during installation.
W
ArrAnTy
The warranty is for Full One Year on the entire unit; Full 2nd through
5th Year on the entire sealed refrigerant system components;
Limited Second through Fifth Year on functional parts only.
5th Year on the entire sealed refrigerant system components;
Limited Second through Fifth Year on functional parts only.
u
niT
d
igiTAl
C
onTrols
The unit’s control must be completely wired and accessible from
the top of the chassis. Controls shall be a LED touch-pad design
with seven large, easy-to-read and use buttons: Heat – Cool –
Off – Fan – Temp+ (plus) – Temp- (minus) and two red seven-
segment LED temperature displays. Unit shall have a green
status LED to advise owner of operational diagnostic messages.
Unit shall have one-button activation via membrane touch-pad.
Unit control board shall have an 18-pin low-voltage connector
to allow for easy connection to remote wired devices. Unit shall
have two serial-port connectors for easy connection to wired or
wireless EMS (Energy Management Systems).
Unit must have the ability to easily configure owner-selectable
and programmable functions:
• Fan-cycle operation
• Electronic temperature limiting for cooling
• Electronic temperature limiting for heating
• Enhanced dehumidification cooling operation
• Unoccupied 18-hour temperature set-back
• Un-rented temperature set-back
• Multiple unit twinning to one wired thermostat
• Load-shedding operation
• Front-desk on-off or temperature set-back
Unit must be able to connect to approved remote devices:
• Wired thermostat
• Wired door motion sensor
• Wired room motion sensor
• Wired room-to-room transfer fan
• Front Desk Control
• Future RF wireless communications devices
Unit must be able to acquire and display operational temperature
data from up to six installed thermistors to include:
• IAT—Indoor air temperature (black)
• ICT—Indoor coil temperature (red )
• IDT—Indoor discharge temperature (yellow)
• OCT—Outdoor coil temperature (blue) (heat pumps & Wire-
the top of the chassis. Controls shall be a LED touch-pad design
with seven large, easy-to-read and use buttons: Heat – Cool –
Off – Fan – Temp+ (plus) – Temp- (minus) and two red seven-
segment LED temperature displays. Unit shall have a green
status LED to advise owner of operational diagnostic messages.
Unit shall have one-button activation via membrane touch-pad.
Unit control board shall have an 18-pin low-voltage connector
to allow for easy connection to remote wired devices. Unit shall
have two serial-port connectors for easy connection to wired or
wireless EMS (Energy Management Systems).
Unit must have the ability to easily configure owner-selectable
and programmable functions:
• Fan-cycle operation
• Electronic temperature limiting for cooling
• Electronic temperature limiting for heating
• Enhanced dehumidification cooling operation
• Unoccupied 18-hour temperature set-back
• Un-rented temperature set-back
• Multiple unit twinning to one wired thermostat
• Load-shedding operation
• Front-desk on-off or temperature set-back
Unit must be able to connect to approved remote devices:
• Wired thermostat
• Wired door motion sensor
• Wired room motion sensor
• Wired room-to-room transfer fan
• Front Desk Control
• Future RF wireless communications devices
Unit must be able to acquire and display operational temperature
data from up to six installed thermistors to include:
• IAT—Indoor air temperature (black)
• ICT—Indoor coil temperature (red )
• IDT—Indoor discharge temperature (yellow)
• OCT—Outdoor coil temperature (blue) (heat pumps & Wire-
less cooler models)
• OAT— Outdoor Air Temperature (Wireless-ready models only)
• Orange—Miscellaneous thermistor or analog device (optional)
• Orange—Miscellaneous thermistor or analog device (optional)
e
vAPorATor
/C
ondenser
f
Ans
Direct drive with a permanent, split-capacitor, two-speed indoor
motor. Condensate must be directed onto the back and sides of
the coil to aid in evaporation and removal.
motor. Condensate must be directed onto the back and sides of
the coil to aid in evaporation and removal.
A
ir
d
isCHArge
Must be a sloped surface so that obstructions cannot be placed
on the unit. Discharge conditioned air can be directed into the
room at an angle of 16 or 56 degrees from the vertical position.
The discharge grille must be of polycarbonate material to resist
bending, cracking, rusting and corrosion.
on the unit. Discharge conditioned air can be directed into the
room at an angle of 16 or 56 degrees from the vertical position.
The discharge grille must be of polycarbonate material to resist
bending, cracking, rusting and corrosion.
C
onTrACTor
'
s
b
id
s
HeeT