Справочник Пользователя для Sunpentown WA1222S
Do not, under any
circumstances, cut,
remove, or bypass
the grounding prong.
circumstances, cut,
remove, or bypass
the grounding prong.
Power supply cord
with 3-prong grounding plug
and current detection device
with 3-prong grounding plug
and current detection device
Grounding type wall
receptacle
receptacle
WARNING
NOTE:
The power supply cord with this air
conditioner contains a current detection
device designed to reduce the risk of fire.
Please refer to the section Operation
of Current Device for details. In the event
that the power supply cord is damaged,
it cannot be repaired, it must be replaced
with a cord from the manufacturer.
conditioner contains a current detection
device designed to reduce the risk of fire.
Please refer to the section Operation
of Current Device for details. In the event
that the power supply cord is damaged,
it cannot be repaired, it must be replaced
with a cord from the manufacturer.
Avoid fire hazard or electric shock. Do not
use an extension cord or an adaptor plug.
Do not remove any prong from the power
cord.
use an extension cord or an adaptor plug.
Do not remove any prong from the power
cord.
WARNING
For Your Safety
WARNING
Prevent Accidents
WARNING
Electrical Information
Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
of this or any other appliance.
Operation of Cur rent Device
The power supply cord contains a current device that senses
damage to the power cord. To test your power supply cord do
the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug
head. Press the TEST button, you will notice a click as the
RESET button pops out.
3. Press the RESET button, again you will notice a click as
the button engages.
4. The power supply cord is now supplying electricity to the
unit. (On some products this is also indicated by a light on
the plug head.)
damage to the power cord. To test your power supply cord do
the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug
head. Press the TEST button, you will notice a click as the
RESET button pops out.
3. Press the RESET button, again you will notice a click as
the button engages.
4. The power supply cord is now supplying electricity to the
unit. (On some products this is also indicated by a light on
the plug head.)
3
To reduce the risk of fire, electrical shock, or injury to persons when using your
air conditioner, follow basic precautions, including the following:
· Be sure the electrical service is adequate for the model you have chosen. This
information can be found on the serial plate, which is located on the side of the
the cabinet and behind the grille.
· If the air conditioner i s t o b e in stalled in a w indow, yo
air conditioner, follow basic precautions, including the following:
· Be sure the electrical service is adequate for the model you have chosen. This
information can be found on the serial plate, which is located on the side of the
the cabinet and behind the grille.
· If the air conditioner i s t o b e in stalled in a w indow, yo
u w ill pr obably w ant to cl ean
both sides of the g lass f irst. I f th e w indow is a tri ple-track ty pe w ith a sc reen pa nel
included, remove the screen completely before installation.
· Be sure the air c onditioner h as b een s ecurely a nd c orrectly in stalled a ccording to
the installation instructions in this manual. Save this manual for possible future
use in removing or installing this unit.
· When handling the air conditioner, be careful to avoid cuts f rom s harp m
included, remove the screen completely before installation.
· Be sure the air c onditioner h as b een s ecurely a nd c orrectly in stalled a ccording to
the installation instructions in this manual. Save this manual for possible future
use in removing or installing this unit.
· When handling the air conditioner, be careful to avoid cuts f rom s harp m
etal f ins
(front and rear coils).
The complete electrical rating of your new room air conditioner is stated on the
serial plate. Refer to the rating when checking the electrical requirements.
· Be sure the air conditioner is properly grounded. To minimize shock and fire
hazards, proper grounding is important. The power cord is equipped with a
three-prong grounding plug for protection against shock hazards.
· Your air conditioner must be used in a properly grounded wall receptacle. If the
wall receptacle you intend to use is not adequately grounded or protected by a
time delay fuse or circuit breaker, have a qualified electrician install the proper
receptacle. Ensure the receptacle is accessible after the unit installation.
· Do not run air conditioner without side protective cover in place. This could
result in mechanical damage within the air conditioner.
·
serial plate. Refer to the rating when checking the electrical requirements.
· Be sure the air conditioner is properly grounded. To minimize shock and fire
hazards, proper grounding is important. The power cord is equipped with a
three-prong grounding plug for protection against shock hazards.
· Your air conditioner must be used in a properly grounded wall receptacle. If the
wall receptacle you intend to use is not adequately grounded or protected by a
time delay fuse or circuit breaker, have a qualified electrician install the proper
receptacle. Ensure the receptacle is accessible after the unit installation.
· Do not run air conditioner without side protective cover in place. This could
result in mechanical damage within the air conditioner.
·
Do not use an extension cord or an adapter plug.
IMPORTANT SAFETY INSTRUCTIONS
· Do not use this device to turn the unit on or off.
· Always make sure the RESET button is pushed in for
correct operation.
· The power supply must be replaced if it fails to reset
when TEST button is pushed or when it cannot be
reset. A new one can be obtained from the manufacturer.
· If power supply cord is damaged, it cannot be repaired. It
MUST be replaced by one obtained from the manufacturer.
· Always make sure the RESET button is pushed in for
correct operation.
· The power supply must be replaced if it fails to reset
when TEST button is pushed or when it cannot be
reset. A new one can be obtained from the manufacturer.
· If power supply cord is damaged, it cannot be repaired. It
MUST be replaced by one obtained from the manufacturer.
NOTE:
NOTE: This air conditioner is designed to operate
under the following conditions:
under the following conditions:
Cooling
Outdoor temp:
Indoor temp:
°
°
64-109 F/18-43 C
°
°
62-90 F/17-32 C
Note: Performance may be reduced outside of these
operating temperatures.
operating temperatures.
For Your Safety
Prevent Accidents
Electrical Information