Инструкции По Установке для Maytag MLE24PDAWW

Скачать
Страница из 44
17
17
Pricing
After the door is opened following the completion of a cycle, the 
display indicates the cycle price (unless set for free operation). As 
coins or debit inputs arrive, the display will change to lead the user 
through the initiation of a cycle.
There are four (4) types of pricing:
Fixed “Vend” Pricing
A dryer set up for “Fixed Cycle” operation can only accept 
additional time accumulated by increments equal to the length of a 
complete dry cycle. A maximum of 99 minutes may be purchased; 
no additional credit is given when 99 minutes is in the display.
Accumulator Pricing
If the price is set to one coin 1, then accumulator mode is in effect 
(stacked PD models also require Fixed Cycle with Top Off option to 
be selected). Cycle time can be purchased one coin at a time (PD 
models) up to the maximum time of 99 minutes. Stacked PD dryers 
will credit all money to a cycle with a single button press while in 
accumulator pricing.
Fixed Cycle With Top Off Pricing
A dryer set to offer “Top Off” capability will allow time to be 
added to an existing dry cycle in increments equal to the number 
of minutes of dry time per quarter (coin 1), up to 99 minutes, 
regardless of the cost required to start the dryer. No credit is given 
for coins or debit inputs entered when the control is displaying 99 
minutes. 
PR Models: In Enhanced Debit Mode, the top off price can be set 
independently. (See VALUE OF COIN 2), and the top off time is 
calculated according to the following equation:
 
top off price  = 
top off time 
 
full cycle price   
full cycle length
Penny increment offset is not applied to top off purchases.
Free Cycles
This is established by setting the cycle price to zero. When this 
happens, “SELECT CYCLE” will appear rather than a cycle price.  
Any cycle started as a free cycle will automatically terminate when 
the door is opened.
Debit Card Ready
This appliance is debit card “cable” ready. It will accept a variety of 
debit card systems, but does NOT come with a debit card reader. 
Refer to the debit card reader manufacturer for proper dryer control 
set-up. In models converted to a Generation 1 debit card system, 
debit pulses represent the equivalent of one coin (coin 1).
CONTROL SET-UP PROCEDURES
IMPORTANT: Read all instructions before operating.
The fabric setting key pads along with the digital display are used to 
set up the dryer controls. 
The display can contain 4 numbers and/or letters and a decimal 
point. These are used to indicate the set-up codes and related code 
values available for use in programming the appliance. 
How to use the key pads to program the controls
1.  
The WHITES AND COLORS key pad is used to adjust the 
values associated with set-up codes. Pressing the key pad will 
increment the value by one (1). Rapid adjustment is possible by  
holding the key pad down. 
2.  The PERM. PRESS key pad will advance you through the 
set-up codes. Pressing the key pad will advance you to the 
next available set-up code. Holding the key pad down will 
automatically advance through the set-up codes at a rate  
of one (1) per second.
3.  The DELICATES key pad is used to select or deselect options. 
IMPORTANT: The console must not be opened unless power is  
first removed from the dryer. To access connector AA1: 
g
 Unplug dryer or disconnect power. 
g
 Open console, disconnect plug on AA1, close console. 
g
 Plug in dryer or reconnect power. 
n
 Stacked PD Models: Insert access panel key and turn 
   counterclockwise.
n
   Stacked PR Models: Once the debit card reader is installed 
(according to the reader manufacturer’s instructions), the 
set-up mode can be entered by inserting a manual set-up card 
(supplied by the reader manufacturer) into the card slot. 
If manual set-up card is not available, manual set-up mode can be 
entered by turning the access panel key.
The dryer is now in the set-up mode. 
NOTE: It is not necessary to set up the dryer with the following 
codes; the dryer is pre-set at the factory. These codes can be 
used to change settings, if desired.
n
  PD units are pre-set at the factory for fixed cycle price with  
top off.
n
   PR units are pre-set for free cycle operation so they can 
be run without readers or coins. 
DISPLAY
After the dryer has been installed and plugged in, the display will 
show “0 minutes.”
Stacked PR Models 
Once the unit has been plugged in and the dryer door opened and 
closed, the display will show the price. In PR and PN models set for 
free cycles, the display will flash “SELECT CYCLE” (not shown).
Stacked PD Models 
PRICE
PRICE
PRICE
PRICE
PRICE
PRICE