Инструкция С Настройками для Summit SEH1536
9
FRAMING BEHIND DRYWALL
wood wall with minimum
thicknes of 8 mm
thicknes of 8 mm
A
B
Ø8
Ø8
A
B
Ø10
Ø10
B
B
D
C
Ø10
Ø10
INSTALLING MOUNTING BRACKETS
1.
1.
Construct wood wall framing with
minimum thickness of 8 mm (0.3") that
is flush with interior surface of wall
studs.
Make sure:
a.
minimum thickness of 8 mm (0.3") that
is flush with interior surface of wall
studs.
Make sure:
a.
the framing is centered over
installation location;
installation location;
b.
the height of the framing will allow
the mounting brackets to be
secured to the framing.
the mounting brackets to be
secured to the framing.
2.
After wall surface is finished, secure
mounting brackets to framing using the
assembly scheme.
mounting brackets to framing using the
assembly scheme.
Fix the connector box to the motor junction plate
with two 3,5 x 9,5 RYSB screws as shown.
with two 3,5 x 9,5 RYSB screws as shown.
Ø10
Ø10
wood wall
INSTALLING THE RANGE HOOD ON THE
WALL
1. Bore the suspender holes:
WALL
1. Bore the suspender holes:
Use the assembly template to bore
holes. Using a Ø 10mm drill bit, drill 4
holes A, B, C, D into the wall. With the
same drill bit, drill 2 holes (E, F) to screw
on the chimney mounting plate. Drill
holes must be about 9/16" (15 mm)
below the ceiling.
holes. Using a Ø 10mm drill bit, drill 4
holes A, B, C, D into the wall. With the
same drill bit, drill 2 holes (E, F) to screw
on the chimney mounting plate. Drill
holes must be about 9/16" (15 mm)
below the ceiling.
2. Fix the inserts:
Fix 4 inserts of Ø 10mm into the holes A,
B, C and D.
Fix 2 inserts of Ø 10mm into the holes E
and F.
B, C and D.
Fix 2 inserts of Ø 10mm into the holes E
and F.
14
Check Electric connection.
(Supply voltage should be 1
10-120 V
, hood
should be connected to grounded socket.)
Check lamp switch.
(Lamp switch should be in on position.)
Hood does not operate
Illumination lamp
does not illuminate
does not illuminate
Air suction of
hood is weak
It does not exhaust
air(in the ambient
without chimney)
hood is weak
It does not exhaust
air(in the ambient
without chimney)
Check motor switch.
(Motor switch should be in I,II,III position)
Check aluminum filter
.
(Aluminum cassette filter should be washed once a month
under normal conditions.)
Check bulbs.
(Bulbs should be in good conditions.)
Check air outlet chimney
.
(Air outlet chimney should be open.)
Check carbon filter
.
(If it operates with carbon filter
, carbon filter should be
replaced quarterly
.)
X
X
X
X
X
X
X
X
X
X
TROUBLESHOOTING
If hood does not operate, before contacting customer service:
Be sure that the power cable is connected to the power supply and that the electric
fuse for the installation is in good condition. Before contacting the service, check
your hood according to the table below. If the problem continues, contact your dealer
or authorized service center.
Troubleshooting Guide
Be sure that the power cable is connected to the power supply and that the electric
fuse for the installation is in good condition. Before contacting the service, check
your hood according to the table below. If the problem continues, contact your dealer
or authorized service center.
Troubleshooting Guide
Service and Spare Parts
You can obtain service advice and spare parts for your product directly from
SUMMIT by calling us at 1-800-932-4267 or by going to our website at
www.summitappliance.com/support
Have the model number of your range hood handy. This can be found on the
product label, which can be seen when you remove the aluminum cassette filter.
You can obtain service advice and spare parts for your product directly from
SUMMIT by calling us at 1-800-932-4267 or by going to our website at
www.summitappliance.com/support
Have the model number of your range hood handy. This can be found on the
product label, which can be seen when you remove the aluminum cassette filter.
An exploded view, parts list and wiring diagram for your unit can be found on the
following pages of this manual.
following pages of this manual.