Инструкции По Установке для Best PK2245
5
1. INSTALL DUCTWORK AND ELECTRICAL WIRING
For a PKEX22 series power pack, either an external blower or in-line blower must be used. The PKEX22 series power pack must be
installed with blower models ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted (blowers sold
separately.)
If installing external or in-line blower, refer to instructions packed with blower and follow steps 1 to 6, 11 to 16, 18 and up of this
manual.
Plan where and how the ductwork will be installed.
A straight, short duct run will allow the power pack to perform most efficiently. Long duct runs, elbows and transitions will reduce the
performance of the power pack. Use as few of them as possible. Larger ducting may be required for longer duct runs.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Connect metal ductwork to cap and work
back towards the hood location. Use 2” metal foil duct tape to seal the joints.
The minimum power pack distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is recommended
for best capture of cooking impurities.
Distances over 30” are at the installer and users discretion.
installed with blower models ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted (blowers sold
separately.)
If installing external or in-line blower, refer to instructions packed with blower and follow steps 1 to 6, 11 to 16, 18 and up of this
manual.
Plan where and how the ductwork will be installed.
A straight, short duct run will allow the power pack to perform most efficiently. Long duct runs, elbows and transitions will reduce the
performance of the power pack. Use as few of them as possible. Larger ducting may be required for longer duct runs.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Connect metal ductwork to cap and work
back towards the hood location. Use 2” metal foil duct tape to seal the joints.
The minimum power pack distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is recommended
for best capture of cooking impurities.
Distances over 30” are at the installer and users discretion.
HH0189A
P
OWER
PACK
R
OOF
CAP
W
ALL
CAP
10” R
OUND
DUCT
10” R
OUND
ADAPTER
24”
TO
30”
ABOVE
COOKING
SURFACE
10” R
OUND
ELBOW
10” V
ERTICAL
DAMPER
I
N
-
LINE
BLOWER
10” R
OUND
DUCT
(
EXCEPT
ILB3, 8’’ R
OUND
DUCT
)
HH0190A
24”
TO
30”
ABOVE
COOKING
SURFACE
R
OOF
CAP
W
ALL
CAP
P
OWER
PACK
HH0191A
P
OWER
PACK
E
XTERNAL
BLOWER
10” R
OUND
DUCT
24”
TO
30”
ABOVE
COOKING
SURFACE
10” R
OUND
ELBOW
E
XTERNAL
BLOWER
PK22 D
UAL
I
NTERNAL
B
LOWER
T
YPICAL
D
UCTWORK
PKEX22
I
N
-
LINE
B
LOWER
T
YPICAL
D
UCTWORK
(
BLOWER
LOCATION
IS
SHOWN
FOR
REFERENCE
ONLY
)
PKEX22 E
XTERNAL
B
LOWER
T
YPICAL
D
UCTWORK
NOTE: For external blowers mounted in
close proximity to power pack,
sound level may be higher than
specified for internal blowers.
sound level may be higher than
specified for internal blowers.
2. PREPARE THE INSTALLATION
WARNING
!
When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer.
Make sure that the following items are included:
- Power
pack
- Installation
instructions
- Accessories:
• 2 Hybrid baffle filters with handles
• Shielded halogen bulbs (120 V, 50 W with GU10 base) (2 for 30” and 39” width power packs, 3 for 45” width power
pack)
• 10” round adapter and 10” round damper (included with PK22 power pack series only, not with PKEX22 series)
• Bag of parts including: 1 wire clamp, 2 wire connectors, 2 no. 8 x 3/8” screws, 6 no. 8-18 x 1¼” chrome plated screws.
If applicable, discard extra screws.