Инструкции По Установке для Smeg ST8246U
e
h
t
s
s
a
p
o
t
d
e
ri
u
q
e
r
si
)
”
2
3
/
5
(
m
c
8
t
s
a
el
t
a
f
o
r
e
t
e
m
ai
d
a
h
ti
w
el
o
h
h
g
u
o
r
h
t
A
hoses and power cord (ref. A fi g. 5-04).
Make sure there area no rough edges that could damage the power cord or
hoses. If the dishwasher is installed in a metal unit protect the edge of the
through hole for the hoses and power cord with a gasket. Do not use extension
cords when making the electrical connection as these do not guarantee safety.
ATTENTION!
INSTALLING THE DISHWASHER IN A NARROW SPACE MAY BEND
OR CRUSH THE POWER CORD. TAKE GREAT CARE IN ORDER TO
REDUCE THE POSSIBILITY OF DAMAGING THE POWER CORD
WHEN INSTALLING OR REMOVING THE APPLIANCE.
A
y
l
p
p
u
s
r
e
t
a
w
e
h
t
o
t
g
n
it
c
e
n
n
o
C
1
.
2
.
5
PREVENTING THE RISK OF CLOGGING OR DAMAGE: IF THE
WATER PIPE IS NEW OR HAS NOT BEEN USED FOR A LONG
TIME, BEFORE CONNECTING TO THE WATER SUPPLY CHECK
THAT THE WATER IS CLEAR AND FREE OF IMPURITIES, TO PRE-
VENT DAMAGE TO THE APPLIANCE. THE DISHWASHER MUST
ALWAYS BE CONNECTED TO THE WATER SYSTEM WITH
NEW HOSES; OLD OR USED HOSES MUST NEVER BE RE-
USED.
Fig. 5-04
e
h
t
s
s
a
p
o
t
d
e
ri
u
q
e
r
si
)”
2
3
/
5
(
m
c
8
t
s
a
el
t
a
f
o
r
e
t
e
m
ai
d
a
h
ti
w
el
o
h
h
g
u
o
r
h
t
A
hoses and power cord (ref. A fig. 5-04).
Make sure there area no rough edges that could damage the power cord or
hoses. If the dishwasher is installed in a metal unit protect the edge of the
through hole for the hoses and power cord with a gasket. Do not use extension
cords when making the electrical connection as these do not guarantee safety.
ATTENTION!
INSTALLING THE DISHWASHER IN A NARROW SPACE MAY BEND
OR CRUSH THE POWER CORD. TAKE GREAT CARE IN ORDER TO
REDUCE THE POSSIBILITY OF DAMAGING THE POWER CORD
WHEN INSTALLING OR REMOVING THE APPLIANCE.
A
y
l
p
p
u
s
r
e
t
a
w
e
h
t
o
t
g
n
it
c
e
n
n
o
C
1
.
2
.
5
PREVENTING THE RISK OF CLOGGING OR DAMAGE: IF THE
WATER PIPE IS NEW OR HAS NOT BEEN USED FOR A LONG
TIME, BEFORE CONNECTING TO THE WATER SUPPLY CHECK
THAT THE WATER IS CLEAR AND FREE OF IMPURITIES, TO PRE-
VENT DAMAGE TO THE APPLIANCE. THE DISHWASHER MUST
ALWAYS BE CONNECTED TO THE WATER SYSTEM WITH
NEW HOSES; OLD OR USED HOSES MUST NEVER BE RE-
USED.
Fig. 5-04
5.2.1.1 Connecting to the water tap
d
ei
l
p
p
u
s
e
h
t
g
n
it
t
fi
,
p
a
t
r
e
t
a
w
d
l
o
c
s
a
g
”
¾
d
e
d
a
e
r
h
t
a
o
t
e
s
o
h
t
el
n
i
e
h
t
t
c
e
n
n
o
C
fi lter (ref. A fi g. 5-05). Firmly secure the hose by tightening the relative
ring nut with your hands (ref. B fi g. 5-05); fi nish by tightening another
¼ turn using a pair of plumbing pliers. For models fi tted with ACQUAS-
TOP (ref. C fi g. 5-05) the fi lter is already present in the threaded ring nut.
The dishwasher can be fi lled with water at a temperature of less than
60°C (140°F).
If the appliance is fi lled with hot water, washing times will be reduced by about
20 minutes, but effi ciency will be slightly impaired. Make the connection to the
domestic hot water tap using the same methods described for connecting the
appliance to the cold water tap.
• Recommended temperature: 49°C (120°F), max. 60°C (140°F).
• Recommended water pressure: 0.5 - 9 bar (7 -130 PSI).
.r
e
c
u
d
e
r
e
r
u
s
s
e
r
p
a
t
fi
,
h
g
i
h
o
o
t
si
e
r
u
s
s
e
r
p
e
h
t
fI
A rubber hose connected to a sink spray may burst if installed on the
same pipes feeding the dishwasher. If your sink is fi tted with this ac-
cessory, remove the hose and plug the hole.
Fig. 5-05
EN
15
INSTALLATION INSTRUCTION