Техническое Описание для Marvel 68-Bottle Digital Wine Cellar - Black Cabinet and Overlay Door
Overlay Panels
For comprehensive installation instructions,
please visit www.marvelrefrigeration.com
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Figure 8
Door should be
parallel to top
and sides of
refrigerator.
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8” allen
wrench. Remove the door by angling the top of the door out-
ward and lifting the door off the bottom hinge.
(See detail in Figure 8).
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it. Remove
the door gasket by peeling up and out of the channel.
Step 4: Cut overlay panel
Depending on the wine cellar model cut the overlay panel to the
dimensions shown. Use Figure 9 and Table A for solid door mod-
els or use Figure 10 and Table B for glass door models.
H
W
Front of
overlay
panel
Figure 9
NOTE
NOTE
For overlay with lock option panel thickness to be
3/4” (19mm) maximum to 5/8” (16mm) minimum.
Weight of the overlay panel should not exceed 20 pounds (9.1
kilograms).
For the door to close properly it is necessary to maintain a
minimum space of 9/32” (7mm) between the door and cabinet
flange (see Figure 8). This space can be adjusted by adjusting the
top and bottom hinge adapter brackets.
Hinge adapter bracket lo-
cated on the top and bottom
of the door.
Remove top
hinge pin to re-
move the door.
9/32”
(7mm)
Model
W
H
3SWCE
14-5/8”
(37.13cm)
30-5/16”
(76.99cm)
6SWCE
23-5/8”
(59.99cm)
30-5/16”
(76.99cm)
Table A
Solid Door Models
Solid Door Models
19
Step 1: Verify door alignment
Verify that the door is aligned correctly with the cabinet prior
to fabricating the custom panel. Failure to do so could result in
mis-alignment of the custom panel with the hinge bracket. The
door should be parallel to the sides and top of the refrigerator.
If alignment is necessary the door may be adjusted by loosen-
ing the 2 screws which secure the upper and/or lower hinge
adapter brackets, located on the top and bottom of the door,
and adjusting the door side to side. Use a 5/32” allen wrench for
this procedure. (See Figure 8 below). When finished aligning the
door, tighten the screws securely.
W
Front of
overlay
panel
Figure 10
1-23/32”
(38.77cm)
Typical 4
Sides
Glass Door Models
H
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Figure 8
Door should be
parallel to top
and sides of
refrigerator.
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8” allen
wrench. Remove the door by angling the top of the door out-
ward and lifting the door off the bottom hinge.
(See detail in Figure 8).
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it. Remove
the door gasket by peeling up and out of the channel.
Step 4: Cut overlay panel
Depending on the wine cellar model cut the overlay panel to the
dimensions shown. Use Figure 9 and Table A for solid door mod-
els or use Figure 10 and Table B for glass door models.
H
W
Front of
overlay
panel
Figure 9
NOTE
NOTE
For overlay with lock option panel thickness to be
3/4” (19mm) maximum to 5/8” (16mm) minimum.
Weight of the overlay panel should not exceed 20 pounds (9.1
kilograms).
For the door to close properly it is necessary to maintain a
minimum space of 9/32” (7mm) between the door and cabinet
flange (see Figure 8). This space can be adjusted by adjusting the
top and bottom hinge adapter brackets.
Hinge adapter bracket lo-
cated on the top and bottom
of the door.
Remove top
hinge pin to re-
move the door.
9/32”
(7mm)
Model
W
H
3SWCE
14-5/8”
(37.13cm)
30-5/16”
(76.99cm)
6SWCE
23-5/8”
(59.99cm)
30-5/16”
(76.99cm)
Table A
Solid Door Models
Solid Door Models
19
Step 1: Verify door alignment
Verify that the door is aligned correctly with the cabinet prior
to fabricating the custom panel. Failure to do so could result in
mis-alignment of the custom panel with the hinge bracket. The
door should be parallel to the sides and top of the refrigerator.
If alignment is necessary the door may be adjusted by loosen-
ing the 2 screws which secure the upper and/or lower hinge
adapter brackets, located on the top and bottom of the door,
and adjusting the door side to side. Use a 5/32” allen wrench for
this procedure. (See Figure 8 below). When finished aligning the
door, tighten the screws securely.
W
Front of
overlay
panel
Figure 10
1-23/32”
(38.77cm)
Typical 4
Sides
Glass Door Models
H
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Figure 8
Door should be
parallel to top
and sides of
refrigerator.
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8” allen
wrench. Remove the door by angling the top of the door out-
ward and lifting the door off the bottom hinge.
(See detail in Figure 8).
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it. Remove
the door gasket by peeling up and out of the channel.
Step 4: Cut overlay panel
Depending on the wine cellar model cut the overlay panel to the
dimensions shown. Use Figure 9 and Table A for solid door mod-
els or use Figure 10 and Table B for glass door models.
H
W
Front of
overlay
panel
Figure 9
NOTE
NOTE
For overlay with lock option panel thickness to be
3/4” (19mm) maximum to 5/8” (16mm) minimum.
Weight of the overlay panel should not exceed 20 pounds (9.1
kilograms).
For the door to close properly it is necessary to maintain a
minimum space of 9/32” (7mm) between the door and cabinet
flange (see Figure 8). This space can be adjusted by adjusting the
top and bottom hinge adapter brackets.
Hinge adapter bracket lo-
cated on the top and bottom
of the door.
Remove top
hinge pin to re-
move the door.
9/32”
(7mm)
Model
W
H
3SWCE
14-5/8”
(37.13cm)
30-5/16”
(76.99cm)
6SWCE
23-5/8”
(59.99cm)
30-5/16”
(76.99cm)
Table A
Solid Door Models
Solid Door Models
19
Step 1: Verify door alignment
Verify that the door is aligned correctly with the cabinet prior
to fabricating the custom panel. Failure to do so could result in
mis-alignment of the custom panel with the hinge bracket. The
door should be parallel to the sides and top of the refrigerator.
If alignment is necessary the door may be adjusted by loosen-
ing the 2 screws which secure the upper and/or lower hinge
adapter brackets, located on the top and bottom of the door,
and adjusting the door side to side. Use a 5/32” allen wrench for
this procedure. (See Figure 8 below). When finished aligning the
door, tighten the screws securely.
W
Front of
overlay
panel
Figure 10
1-23/32”
(38.77cm)
Typical 4
Sides
Glass Door Models
H
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Figure 8
Door should be
parallel to top
and sides of
refrigerator.
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8” allen
wrench. Remove the door by angling the top of the door out-
ward and lifting the door off the bottom hinge.
(See detail in Figure 8).
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it. Remove
the door gasket by peeling up and out of the channel.
Step 4: Cut overlay panel
Depending on the wine cellar model cut the overlay panel to the
dimensions shown. Use Figure 9 and Table A for solid door mod-
els or use Figure 10 and Table B for glass door models.
H
W
Front of
overlay
panel
Figure 9
NOTE
NOTE
For overlay with lock option panel thickness to be
3/4” (19mm) maximum to 5/8” (16mm) minimum.
Weight of the overlay panel should not exceed 20 pounds (9.1
kilograms).
For the door to close properly it is necessary to maintain a
minimum space of 9/32” (7mm) between the door and cabinet
flange (see Figure 8). This space can be adjusted by adjusting the
top and bottom hinge adapter brackets.
Hinge adapter bracket lo-
cated on the top and bottom
of the door.
Remove top
hinge pin to re-
move the door.
9/32”
(7mm)
Model
W
H
3SWCE
14-5/8”
(37.13cm)
30-5/16”
(76.99cm)
6SWCE
23-5/8”
(59.99cm)
30-5/16”
(76.99cm)
Table A
Solid Door Models
Solid Door Models
19
Step 1: Verify door alignment
Verify that the door is aligned correctly with the cabinet prior
to fabricating the custom panel. Failure to do so could result in
mis-alignment of the custom panel with the hinge bracket. The
door should be parallel to the sides and top of the refrigerator.
If alignment is necessary the door may be adjusted by loosen-
ing the 2 screws which secure the upper and/or lower hinge
adapter brackets, located on the top and bottom of the door,
and adjusting the door side to side. Use a 5/32” allen wrench for
this procedure. (See Figure 8 below). When finished aligning the
door, tighten the screws securely.
W
Front of
overlay
panel
Figure 10
1-23/32”
(38.77cm)
Typical 4
Sides
Glass Door Models
H
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Figure 8
Door should be
parallel to top
and sides of
refrigerator.
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8” allen
wrench. Remove the door by angling the top of the door out-
ward and lifting the door off the bottom hinge.
(See detail in Figure 8).
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it. Remove
the door gasket by peeling up and out of the channel.
Step 4: Cut overlay panel
Depending on the wine cellar model cut the overlay panel to the
dimensions shown. Use Figure 9 and Table A for solid door mod-
els or use Figure 10 and Table B for glass door models.
H
W
Front of
overlay
panel
Figure 9
NOTE
NOTE
For overlay with lock option panel thickness to be
3/4” (19mm) maximum to 5/8” (16mm) minimum.
Weight of the overlay panel should not exceed 20 pounds (9.1
kilograms).
For the door to close properly it is necessary to maintain a
minimum space of 9/32” (7mm) between the door and cabinet
flange (see Figure 8). This space can be adjusted by adjusting the
top and bottom hinge adapter brackets.
Hinge adapter bracket lo-
cated on the top and bottom
of the door.
Remove top
hinge pin to re-
move the door.
9/32”
(7mm)
Model
W
H
3SWCE
14-5/8”
(37.13cm)
30-5/16”
(76.99cm)
6SWCE
23-5/8”
(59.99cm)
30-5/16”
(76.99cm)
Table A
Solid Door Models
Solid Door Models
19
Step 1: Verify door alignment
Verify that the door is aligned correctly with the cabinet prior
to fabricating the custom panel. Failure to do so could result in
mis-alignment of the custom panel with the hinge bracket. The
door should be parallel to the sides and top of the refrigerator.
If alignment is necessary the door may be adjusted by loosen-
ing the 2 screws which secure the upper and/or lower hinge
adapter brackets, located on the top and bottom of the door,
and adjusting the door side to side. Use a 5/32” allen wrench for
this procedure. (See Figure 8 below). When finished aligning the
door, tighten the screws securely.
W
Front of
overlay
panel
Figure 10
1-23/32”
(38.77cm)
Typical 4
Sides
Glass Door Models
H
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Material Type
Pilot Hole for #8 Wood Screw
Hardwood
1/8” (3.2mm) Diameter. Pilot Hole
Softwood
7/64 (2.8mm) Diameter. Pilot Hole
Table C
If your refrigerator has a door lock proceed to Step 7. If your
refrigerator does not have a door lock proceed to Step 9.
NOTE
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the location of the lock hole on
the overlay panel, this is the hole in the top corner of the handle
side of the door. Remove the clamp and remove the overlay
panel from the door. On the backside of the panel where you
marked the lock location drill a 13/16” (20.5mm) diameter
counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a
15/32” (12.0mm) diameter hole through the overlay panel cen-
tered on the counter bore being careful not to splinter the wood
on the face side of the panel. (See Figure 12).
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the lon-
ger extension for a 3/4” thick overlay panel and the shorter one
for a 5/8” thick panel. Assemble the lock extension, cam stop
washer, spring washer, and set screw to the lock as shown in
Figure 12 and 13. Install this assembly into the overlay panel and
secure with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vertical.
Figure 12
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Model
W
H
3SWCE
14-5/16”
(36.35cm)
30-5/16”
(76.99cm)
6SWCE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
8SWCE
29-7/16”
(74.78cm)
30-5/16”
(76.99cm)
6SDZE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
Table B
Glass Door Models
Top Hinge
Adapter
Hole in hinge
adapter
Door
Overlay panel
Hole in bottom
hinge adapter
Figure 11
20
Step 5: Drill hinge clearance holes in overlay panel
Set the overlay panel on the door front, align the edges, and
clamp together. Clamp the panel firmly but be careful not to
damage the door or the panel. Mark center of hinge adapter
hole on wood panel, top and bottom. (See Figure 11). Remove
wood panel from door and drill 5/16” (8mm) diameter clearance
holes into the overlay panels 3/4” (20mm) deep. These will be
clearance holes for the top and bottom hinge pins.
This is also a convenient time to locate and drill the holes for
your handle. Most often the handle is to match that of the sur-
rounding cabinetry. If your handle attaches from the back-side
of the custom panel, locate the mounting holes while the panel
is attached to the door and cabinet. After the panel is removed
from the door, drill the mounting holes from the front, to the
recommended diameter of the handle manufacturer. Counter
bore the back-side of the panel so the screw heads do not inter-
fere with the surface of the door.
Step 6: Drill panel mounting holes
Re-clamp the panel to the door per step 5 and drill the screw
pilot holes for attaching the overlay panel to the door. Select
the size of the hole from Table C. Be careful not to drill the pilot
holes through the overlay panel, (1/2” (12.7mm) deep for 3/4”
(19mm) and 5/8” (15.7mm) panels ).
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Material Type
Pilot Hole for #8 Wood Screw
Hardwood
1/8” (3.2mm) Diameter. Pilot Hole
Softwood
7/64 (2.8mm) Diameter. Pilot Hole
Table C
If your refrigerator has a door lock proceed to Step 7. If your
refrigerator does not have a door lock proceed to Step 9.
NOTE
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the location of the lock hole on
the overlay panel, this is the hole in the top corner of the handle
side of the door. Remove the clamp and remove the overlay
panel from the door. On the backside of the panel where you
marked the lock location drill a 13/16” (20.5mm) diameter
counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a
15/32” (12.0mm) diameter hole through the overlay panel cen-
tered on the counter bore being careful not to splinter the wood
on the face side of the panel. (See Figure 12).
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the lon-
ger extension for a 3/4” thick overlay panel and the shorter one
for a 5/8” thick panel. Assemble the lock extension, cam stop
washer, spring washer, and set screw to the lock as shown in
Figure 12 and 13. Install this assembly into the overlay panel and
secure with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vertical.
Figure 12
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Model
W
H
3SWCE
14-5/16”
(36.35cm)
30-5/16”
(76.99cm)
6SWCE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
8SWCE
29-7/16”
(74.78cm)
30-5/16”
(76.99cm)
6SDZE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
Table B
Glass Door Models
Top Hinge
Adapter
Hole in hinge
adapter
Door
Overlay panel
Hole in bottom
hinge adapter
Figure 11
20
Step 5: Drill hinge clearance holes in overlay panel
Set the overlay panel on the door front, align the edges, and
clamp together. Clamp the panel firmly but be careful not to
damage the door or the panel. Mark center of hinge adapter
hole on wood panel, top and bottom. (See Figure 11). Remove
wood panel from door and drill 5/16” (8mm) diameter clearance
holes into the overlay panels 3/4” (20mm) deep. These will be
clearance holes for the top and bottom hinge pins.
This is also a convenient time to locate and drill the holes for
your handle. Most often the handle is to match that of the sur-
rounding cabinetry. If your handle attaches from the back-side
of the custom panel, locate the mounting holes while the panel
is attached to the door and cabinet. After the panel is removed
from the door, drill the mounting holes from the front, to the
recommended diameter of the handle manufacturer. Counter
bore the back-side of the panel so the screw heads do not inter-
fere with the surface of the door.
Step 6: Drill panel mounting holes
Re-clamp the panel to the door per step 5 and drill the screw
pilot holes for attaching the overlay panel to the door. Select
the size of the hole from Table C. Be careful not to drill the pilot
holes through the overlay panel, (1/2” (12.7mm) deep for 3/4”
(19mm) and 5/8” (15.7mm) panels ).
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Material Type
Pilot Hole for #8 Wood Screw
Hardwood
1/8” (3.2mm) Diameter. Pilot Hole
Softwood
7/64 (2.8mm) Diameter. Pilot Hole
Table C
If your refrigerator has a door lock proceed to Step 7. If your
refrigerator does not have a door lock proceed to Step 9.
NOTE
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the location of the lock hole on
the overlay panel, this is the hole in the top corner of the handle
side of the door. Remove the clamp and remove the overlay
panel from the door. On the backside of the panel where you
marked the lock location drill a 13/16” (20.5mm) diameter
counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a
15/32” (12.0mm) diameter hole through the overlay panel cen-
tered on the counter bore being careful not to splinter the wood
on the face side of the panel. (See Figure 12).
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the lon-
ger extension for a 3/4” thick overlay panel and the shorter one
for a 5/8” thick panel. Assemble the lock extension, cam stop
washer, spring washer, and set screw to the lock as shown in
Figure 12 and 13. Install this assembly into the overlay panel and
secure with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vertical.
Figure 12
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Model
W
H
3SWCE
14-5/16”
(36.35cm)
30-5/16”
(76.99cm)
6SWCE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
8SWCE
29-7/16”
(74.78cm)
30-5/16”
(76.99cm)
6SDZE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
Table B
Glass Door Models
Top Hinge
Adapter
Hole in hinge
adapter
Door
Overlay panel
Hole in bottom
hinge adapter
Figure 11
20
Step 5: Drill hinge clearance holes in overlay panel
Set the overlay panel on the door front, align the edges, and
clamp together. Clamp the panel firmly but be careful not to
damage the door or the panel. Mark center of hinge adapter
hole on wood panel, top and bottom. (See Figure 11). Remove
wood panel from door and drill 5/16” (8mm) diameter clearance
holes into the overlay panels 3/4” (20mm) deep. These will be
clearance holes for the top and bottom hinge pins.
This is also a convenient time to locate and drill the holes for
your handle. Most often the handle is to match that of the sur-
rounding cabinetry. If your handle attaches from the back-side
of the custom panel, locate the mounting holes while the panel
is attached to the door and cabinet. After the panel is removed
from the door, drill the mounting holes from the front, to the
recommended diameter of the handle manufacturer. Counter
bore the back-side of the panel so the screw heads do not inter-
fere with the surface of the door.
Step 6: Drill panel mounting holes
Re-clamp the panel to the door per step 5 and drill the screw
pilot holes for attaching the overlay panel to the door. Select
the size of the hole from Table C. Be careful not to drill the pilot
holes through the overlay panel, (1/2” (12.7mm) deep for 3/4”
(19mm) and 5/8” (15.7mm) panels ).
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Material Type
Pilot Hole for #8 Wood Screw
Hardwood
1/8” (3.2mm) Diameter. Pilot Hole
Softwood
7/64 (2.8mm) Diameter. Pilot Hole
Table C
If your refrigerator has a door lock proceed to Step 7. If your
refrigerator does not have a door lock proceed to Step 9.
NOTE
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the location of the lock hole on
the overlay panel, this is the hole in the top corner of the handle
side of the door. Remove the clamp and remove the overlay
panel from the door. On the backside of the panel where you
marked the lock location drill a 13/16” (20.5mm) diameter
counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a
15/32” (12.0mm) diameter hole through the overlay panel cen-
tered on the counter bore being careful not to splinter the wood
on the face side of the panel. (See Figure 12).
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the lon-
ger extension for a 3/4” thick overlay panel and the shorter one
for a 5/8” thick panel. Assemble the lock extension, cam stop
washer, spring washer, and set screw to the lock as shown in
Figure 12 and 13. Install this assembly into the overlay panel and
secure with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vertical.
Figure 12
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Model
W
H
3SWCE
14-5/16”
(36.35cm)
30-5/16”
(76.99cm)
6SWCE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
8SWCE
29-7/16”
(74.78cm)
30-5/16”
(76.99cm)
6SDZE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
Table B
Glass Door Models
Top Hinge
Adapter
Hole in hinge
adapter
Door
Overlay panel
Hole in bottom
hinge adapter
Figure 11
20
Step 5: Drill hinge clearance holes in overlay panel
Set the overlay panel on the door front, align the edges, and
clamp together. Clamp the panel firmly but be careful not to
damage the door or the panel. Mark center of hinge adapter
hole on wood panel, top and bottom. (See Figure 11). Remove
wood panel from door and drill 5/16” (8mm) diameter clearance
holes into the overlay panels 3/4” (20mm) deep. These will be
clearance holes for the top and bottom hinge pins.
This is also a convenient time to locate and drill the holes for
your handle. Most often the handle is to match that of the sur-
rounding cabinetry. If your handle attaches from the back-side
of the custom panel, locate the mounting holes while the panel
is attached to the door and cabinet. After the panel is removed
from the door, drill the mounting holes from the front, to the
recommended diameter of the handle manufacturer. Counter
bore the back-side of the panel so the screw heads do not inter-
fere with the surface of the door.
Step 6: Drill panel mounting holes
Re-clamp the panel to the door per step 5 and drill the screw
pilot holes for attaching the overlay panel to the door. Select
the size of the hole from Table C. Be careful not to drill the pilot
holes through the overlay panel, (1/2” (12.7mm) deep for 3/4”
(19mm) and 5/8” (15.7mm) panels ).
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Material Type
Pilot Hole for #8 Wood Screw
Hardwood
1/8” (3.2mm) Diameter. Pilot Hole
Softwood
7/64 (2.8mm) Diameter. Pilot Hole
Table C
If your refrigerator has a door lock proceed to Step 7. If your
refrigerator does not have a door lock proceed to Step 9.
NOTE
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the location of the lock hole on
the overlay panel, this is the hole in the top corner of the handle
side of the door. Remove the clamp and remove the overlay
panel from the door. On the backside of the panel where you
marked the lock location drill a 13/16” (20.5mm) diameter
counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a
15/32” (12.0mm) diameter hole through the overlay panel cen-
tered on the counter bore being careful not to splinter the wood
on the face side of the panel. (See Figure 12).
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the lon-
ger extension for a 3/4” thick overlay panel and the shorter one
for a 5/8” thick panel. Assemble the lock extension, cam stop
washer, spring washer, and set screw to the lock as shown in
Figure 12 and 13. Install this assembly into the overlay panel and
secure with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vertical.
Figure 12
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Model
W
H
3SWCE
14-5/16”
(36.35cm)
30-5/16”
(76.99cm)
6SWCE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
8SWCE
29-7/16”
(74.78cm)
30-5/16”
(76.99cm)
6SDZE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
Table B
Glass Door Models
Top Hinge
Adapter
Hole in hinge
adapter
Door
Overlay panel
Hole in bottom
hinge adapter
Figure 11
20
Step 5: Drill hinge clearance holes in overlay panel
Set the overlay panel on the door front, align the edges, and
clamp together. Clamp the panel firmly but be careful not to
damage the door or the panel. Mark center of hinge adapter
hole on wood panel, top and bottom. (See Figure 11). Remove
wood panel from door and drill 5/16” (8mm) diameter clearance
holes into the overlay panels 3/4” (20mm) deep. These will be
clearance holes for the top and bottom hinge pins.
This is also a convenient time to locate and drill the holes for
your handle. Most often the handle is to match that of the sur-
rounding cabinetry. If your handle attaches from the back-side
of the custom panel, locate the mounting holes while the panel
is attached to the door and cabinet. After the panel is removed
from the door, drill the mounting holes from the front, to the
recommended diameter of the handle manufacturer. Counter
bore the back-side of the panel so the screw heads do not inter-
fere with the surface of the door.
Step 6: Drill panel mounting holes
Re-clamp the panel to the door per step 5 and drill the screw
pilot holes for attaching the overlay panel to the door. Select
the size of the hole from Table C. Be careful not to drill the pilot
holes through the overlay panel, (1/2” (12.7mm) deep for 3/4”
(19mm) and 5/8” (15.7mm) panels ).
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Material Type
Pilot Hole for #8 Wood Screw
Hardwood
1/8” (3.2mm) Diameter. Pilot Hole
Softwood
7/64 (2.8mm) Diameter. Pilot Hole
Table C
If your refrigerator has a door lock proceed to Step 7. If your
refrigerator does not have a door lock proceed to Step 9.
NOTE
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the location of the lock hole on
the overlay panel, this is the hole in the top corner of the handle
side of the door. Remove the clamp and remove the overlay
panel from the door. On the backside of the panel where you
marked the lock location drill a 13/16” (20.5mm) diameter
counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a
15/32” (12.0mm) diameter hole through the overlay panel cen-
tered on the counter bore being careful not to splinter the wood
on the face side of the panel. (See Figure 12).
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the lon-
ger extension for a 3/4” thick overlay panel and the shorter one
for a 5/8” thick panel. Assemble the lock extension, cam stop
washer, spring washer, and set screw to the lock as shown in
Figure 12 and 13. Install this assembly into the overlay panel and
secure with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vertical.
Figure 12
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Model
W
H
3SWCE
14-5/16”
(36.35cm)
30-5/16”
(76.99cm)
6SWCE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
8SWCE
29-7/16”
(74.78cm)
30-5/16”
(76.99cm)
6SDZE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
Table B
Glass Door Models
Top Hinge
Adapter
Hole in hinge
adapter
Door
Overlay panel
Hole in bottom
hinge adapter
Figure 11
20
Step 5: Drill hinge clearance holes in overlay panel
Set the overlay panel on the door front, align the edges, and
clamp together. Clamp the panel firmly but be careful not to
damage the door or the panel. Mark center of hinge adapter
hole on wood panel, top and bottom. (See Figure 11). Remove
wood panel from door and drill 5/16” (8mm) diameter clearance
holes into the overlay panels 3/4” (20mm) deep. These will be
clearance holes for the top and bottom hinge pins.
This is also a convenient time to locate and drill the holes for
your handle. Most often the handle is to match that of the sur-
rounding cabinetry. If your handle attaches from the back-side
of the custom panel, locate the mounting holes while the panel
is attached to the door and cabinet. After the panel is removed
from the door, drill the mounting holes from the front, to the
recommended diameter of the handle manufacturer. Counter
bore the back-side of the panel so the screw heads do not inter-
fere with the surface of the door.
Step 6: Drill panel mounting holes
Re-clamp the panel to the door per step 5 and drill the screw
pilot holes for attaching the overlay panel to the door. Select
the size of the hole from Table C. Be careful not to drill the pilot
holes through the overlay panel, (1/2” (12.7mm) deep for 3/4”
(19mm) and 5/8” (15.7mm) panels ).
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Material Type
Pilot Hole for #8 Wood Screw
Hardwood
1/8” (3.2mm) Diameter. Pilot Hole
Softwood
7/64 (2.8mm) Diameter. Pilot Hole
Table C
If your refrigerator has a door lock proceed to Step 7. If your
refrigerator does not have a door lock proceed to Step 9.
NOTE
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the location of the lock hole on
the overlay panel, this is the hole in the top corner of the handle
side of the door. Remove the clamp and remove the overlay
panel from the door. On the backside of the panel where you
marked the lock location drill a 13/16” (20.5mm) diameter
counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a
15/32” (12.0mm) diameter hole through the overlay panel cen-
tered on the counter bore being careful not to splinter the wood
on the face side of the panel. (See Figure 12).
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the lon-
ger extension for a 3/4” thick overlay panel and the shorter one
for a 5/8” thick panel. Assemble the lock extension, cam stop
washer, spring washer, and set screw to the lock as shown in
Figure 12 and 13. Install this assembly into the overlay panel and
secure with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vertical.
Figure 12
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Model
W
H
3SWCE
14-5/16”
(36.35cm)
30-5/16”
(76.99cm)
6SWCE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
8SWCE
29-7/16”
(74.78cm)
30-5/16”
(76.99cm)
6SDZE
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
Table B
Glass Door Models
Top Hinge
Adapter
Hole in hinge
adapter
Door
Overlay panel
Hole in bottom
hinge adapter
Figure 11
20
Step 5: Drill hinge clearance holes in overlay panel
Set the overlay panel on the door front, align the edges, and
clamp together. Clamp the panel firmly but be careful not to
damage the door or the panel. Mark center of hinge adapter
hole on wood panel, top and bottom. (See Figure 11). Remove
wood panel from door and drill 5/16” (8mm) diameter clearance
holes into the overlay panels 3/4” (20mm) deep. These will be
clearance holes for the top and bottom hinge pins.
This is also a convenient time to locate and drill the holes for
your handle. Most often the handle is to match that of the sur-
rounding cabinetry. If your handle attaches from the back-side
of the custom panel, locate the mounting holes while the panel
is attached to the door and cabinet. After the panel is removed
from the door, drill the mounting holes from the front, to the
recommended diameter of the handle manufacturer. Counter
bore the back-side of the panel so the screw heads do not inter-
fere with the surface of the door.
Step 6: Drill panel mounting holes
Re-clamp the panel to the door per step 5 and drill the screw
pilot holes for attaching the overlay panel to the door. Select
the size of the hole from Table C. Be careful not to drill the pilot
holes through the overlay panel, (1/2” (12.7mm) deep for 3/4”
(19mm) and 5/8” (15.7mm) panels ).