Справочник Пользователя для John Deere 100 Series
Operating - 15
OPERATING
MX4896
b.Turn left blade (C) as shown. Hold drive belt and turn right blade (D) as
shown. Take measurement for both blades.
shown. Take measurement for both blades.
The difference between blade measurements must not be more than 3
mm (1/8 in.).
mm (1/8 in.).
c.Adjust mower deck level, if necessary.
5. Measure mower level (front-to-rear).
MX4896a
a.Turn right blade (E) so blade tip points straight forward.
b.Measure from blade tip to the surface. Take measurement for both
blades.
blades.
The front blade tip must be 3–6 mm (1/8 -1/4 in.) lower than rear blade
tip.
tip.
c.Adjust mower deck level if necessary.
Adjusting Mower Deck Level
NOTE: Mower deck wheels should not contact the ground when
leveling the mower deck.
leveling the mower deck.
Method One
1. Make sure machine is on a flat, level surface.
2. Check that tires are inflated to correct tire pressure. Tire pressure is
marked on the side of the tire.
marked on the side of the tire.
M17687a
Picture Note: 107 cm (42 in.) mower deck shown
3. Place three short 51 mm (2 in.) blocks of wood under the edges (A) of
the mower deck.
the mower deck.
4. Lower mower deck to the 65 mm (2.5 in.) cutting height position.
5. Check that the mower deck is level and lightly touching each of the
three wooden blocks.
MX16561
• If the rear of the mower deck is not touching the rear blocks, or is
sitting heavily on the blocks, adjust the rear lift links by turning the
leveling nut (B) on each lift link. The blocks should be able to easily slide
in and out beneath the mower deck when the mower deck is correctly
adjusted.
sitting heavily on the blocks, adjust the rear lift links by turning the
leveling nut (B) on each lift link. The blocks should be able to easily slide
in and out beneath the mower deck when the mower deck is correctly
adjusted.
MX10529Y
Picture Note: 107 cm (42 in.) mower deck shown
• If the front of the mower deck is not lightly touching the front block,
adjust the front draft arm by turning the nut (C).
adjust the front draft arm by turning the nut (C).
6. Raise the cutting height to the next highest position and remove the
three wooden blocks.
three wooden blocks.
7. Turn the nut (C) on the front draft arm counterclockwise 1-2 full turns so
that the front of the deck is 3-6 mm (1/8-1/4 in.) lower than the rear. This
adjustment prevents “double cutting,” which wastes horsepower and
causes brown grass tips.
that the front of the deck is 3-6 mm (1/8-1/4 in.) lower than the rear. This
adjustment prevents “double cutting,” which wastes horsepower and
causes brown grass tips.
Method Two
NOTE: An optional mower deck leveling gauge (AM130907) is
available from your John Deere dealer. It allows for precision mower
deck leveling by measuring mower deck level at the blade tips.
available from your John Deere dealer. It allows for precision mower
deck leveling by measuring mower deck level at the blade tips.
1. Make sure machine is on a flat, level surface.
2. Check that tires are inflated to correct tire pressure. Tire pressure is
marked on the side of the tire.
marked on the side of the tire.
3. Lower mower deck to the 50 mm (2 in.) cutting height position.
4. With a tape measure or ruler, measure the left rear and right rear edge
of the mower deck at points (A). If the two measurements are not equal,
turn the leveling nut (B) on each rear lift link to adjust. Repeat procedure
until rear corners of the mower deck are level.
of the mower deck at points (A). If the two measurements are not equal,
turn the leveling nut (B) on each rear lift link to adjust. Repeat procedure
until rear corners of the mower deck are level.
E
A
A
A
B
C
C