Справочник Пользователя для Panasonic DMR-ES20

RQT8212

Continued on the next page

•
•

•

•

•

•

Change manufacturer code. Some televisions cannot be operated even if you change the 
code.
The remote control and main unit are using different codes. Change the code on the remote 
control. 

Press and hold [ENTER] and the indicated number button at 
the same time for more than 2 seconds. 

The batteries are depleted. Replace them with new ones.
Coloured glass may obstruct the signal reception/transmission.
Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight exposure.
The child lock function is activated.

•

•

•

Some operations may be prohibited by the disc.
The unit is hot (“U59” appears on the display). Wait for “U59” to disappear. 
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
Press [

8] on the main unit to switch the unit to standby. 

If the unit doesn’t switch to standby, press and hold [

8] on the main unit for about 10 seconds. 

The unit is forcibly switched to standby. 
Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.

•

•
•
•

Timer recording is in recording standby. Press [

z TIMER] to cancel the recording standby.

Linked timer recordings with external equipment is in recording standby (“EXT Link” on the unit’s 
display blinks when [

^ DVD] is pressed). Press [EXT LINK] to cancel the recording standby.

The unit may have a problem. While the unit is off, press and hold [

g] and [CH 1] on the main 

unit at the same time for about 5 seconds. Remove the disc and consult the dealer.
If the Child Lock function is activated, above operation does not work. Cancel the Child Lock function.

•

•

Check the connections.
You must connect to a television equipped with the Q Link function with a fully wired 21-pin 
Scart cable to download channel presets.

•

•
•

Make sure that “Quick Start” is set to “On”.
Even if “Quick Start” is set to “On”, startup is slow if the clock is not set, there was a power 
failure or the AC plug has just been connected.
A few dozen seconds after turning on the unit, you can play a disc or start recording to discs 
other than DVD-RAM.
Startup takes time for a few minutes after 5:15 am due to system maintenance of this unit.

•
•

•
•

•

•
•

•

You haven’t inserted a disc or the disc you inserted cannot be recorded on. Insert a disc the 
unit can record onto. 
The disc is unformatted. Format the disc. 
The write-protect tab on the cartridge is set to PROTECT, or the disc is protected with DISC 
MANAGEMENT.
Some programmes have limitations on the number of times they can be recorded. (CPRM)
The disc is full or nearly full. Erase un-needed titles or use another disc.
You cannot record on finalized DVD-R, DVD-RW (DVD-Video format), +R or DVD-RW (DVD 
Video Recording format) discs.
Due to peculiarities of DVD-R, DVD-RW (DVD-Video format) or +R, you may be unable to 
record onto them if you either insert and remove the disc or switch the unit on and off while a 
disc is loaded, a total of fifty times.
DVD-R, DVD-RW (DVD-Video format) and +R recorded on this unit may not be recordable on 
other Panasonic DVD recorders.

•
•
•

The timer programme is incorrect or different timer programme times overlap. Correct the 
programme.
The unit is not on timer recording standby. (“

z” on the unit’s display is not on.) 

Press [

z TIMER].

Set the clock.

g] is pressed.

•

•

While using timer recording, press [

z TIMER]. (“z” disappears.)

When using the linked timer recording with external equipment, press [EXT LINK]. (“EXT Link” 
disappears.)

•

The timer programme remains if set to daily or weekly.

•

If there is a power failure or the plug is disconnected from the household AC mains socket 
while recording or editing, the title may be lost or the disc may become unusable. You will have 
to format the disc (

) or use a new disc. We cannot offer any guarantee regarding 

lost programmes or discs.

•
•

•
•

If images cannot be recorded or if the recording is aborted, check the connections and DV 
equipment settings.
You cannot start recording until the images from the DV equipment appear on the television.
Recording may not be performed as desired if the time codes on the tape in the DV equipment 
are not successive.
Depending on the equipment, the DV automatic recording may not operate properly.

q] (PLAY) is pressed.

•

•
•
•

Insert the disc correctly with the label facing up.
You tried to play a blank DVD-RAM, DVD-R, DVD-RW (DVD-Video format), +R or DVD-RW 
(DVD Video Recording format) unplayable on this unit.
When recording to DVD-RAM using EP ( 8Hours ) mode, play may not be possible on DVD 
players that are compatible with DVD-RAM. In this case use EP ( 6Hours ) mode.
You cannot play discs during DV automatic recording.

•

Some DVD-Video cannot be played when you change the ratings level.

•

•

The languages are not recorded on the disc.
You may have to use the disc’s menus to select languages. 

•

•

Subtitles are not recorded on the disc.
Turn the subtitles on.