Справочник Пользователя для Mitsubishi Electronics FR-A700
41
Connection of stand-alone option units
2
* Do not remove the jumper across terminal P/+ and P1 except when connecting a DC reactor.
When the regenerative brake transistor is damaged, the following sequence is recommended to prevent overheat
and burnout of the brake resistor.
*1
Since the 11K or higher inverter is not provided with the PX terminal, a jumper is not need to be removed.
*2
Refer to the table below for the type number of each capacity of thermal relay and the diagram below for the connection. (Always install a thermal
relay when using the 11K or higher)
relay when using the 11K or higher)
FR-A720-11K, FR-A740-11K, 15K
FR-A720-15K to 22K, FR-A740-18.5K, 22K
Power Supply
Voltage
High-Duty Brake
Resistor
Thermal Relay Type
(Mitsubishi product)
Contact Rating
200V
FR-ABR-0.4K
TH-N20CXHZ-0.7A
110V 5AAC,
220V 2AAC(AC-11 class)
110V 0.5ADC,
220V 0.25ADC(DC-11 class)
220V 2AAC(AC-11 class)
110V 0.5ADC,
220V 0.25ADC(DC-11 class)
FR-ABR-0.75K
TH-N20CXHZ-1.3A
FR-ABR-2.2K
TH-N20CXHZ-2.1A
FR-ABR-3.7K
TH-N20CXHZ-3.6A
FR-ABR-5.5K
TH-N20CXHZ-5A
FR-ABR-7.5K
TH-N20CXHZ-6.6A
FR-ABR-11K
TH-N20CXHZ-11A
FR-ABR-15K
TH-N20CXHZ-11A
FR-ABR-22K
TH-N60-22A
400V
FR-ABR-H0.4K
TH-N20CXHZ-0.24A
FR-ABR-H0.75K
TH-N20CXHZ-0.35A
FR-ABR-H1.5K
TH-N20CXHZ-0.9A
FR-ABR-H2.2K
TH-N20CXHZ-1.3A
FR-ABR-H3.7K
TH-N20CXHZ-2.1A
FR-ABR-H5.5K
TH-N20CXHZ-2.5A
FR-ABR-H7.5K
TH-N20CXHZ-3.6A
FR-ABR-H11K
TH-N20CXHZ-6.6A
FR-ABR-H15K
TH-N20CXHZ-6.6A
FR-ABR-H22K
TH-N20-9A
CAUTION
⋅ The brake resistor connected should only be the dedicated brake resistor.
⋅ The jumper across terminals PR and PX (7.5K or lower) must be disconnected before connecting the dedicated brake resistor.
⋅ The jumper across terminals PR and PX (7.5K or lower) must be disconnected before connecting the dedicated brake resistor.
Doing so may damage the inverter.
⋅ Brake resistor cannot be used with the brake unit, high power factor converter, power supply regeneration converter, etc.
Jumper *
Terminal P/+
Terminal PR
Brake resistor
Connect the brake resistor
across terminals P/+ and PR.
across terminals P/+ and PR.
Terminal P/+
Terminal PR
Brake resistor
Jumper
*
Connect the brake resistor
across terminals P/+ and PR.
across terminals P/+ and PR.
R
MC
Power
Supply
Supply
High-duty
brake resistor
(FR-ABR)
Thermal
relay
(OCR)(*2)
relay
(OCR)(*2)
Inverter
PX
PR
P/+
S/L2
T/L3
R/L1
Disconnect jumper. (*1)
MC
Power
Supply
Supply
T
F
ON
OFF
MC
MC
OCR
Contact
<Example 1>
<Example 2>
PX
PR
P/+
S/L2
T/L3
R/L1
Inverter
(OCR)(*2)
Thermal
relay
relay
(FR-ABR)
High-duty
brake resistor
R
Disconnect jumper. (*1)
B
C
T
F
ON
OFF
OCR
Contact
MC
MC
To the inverter
P/+ terminal
P/+ terminal
To the ABR
TH-N20
1/L
1
5/L
3
2/T
1
6/T
3