Справочник Пользователя для Samsung RF4287HABP
10_
setting up
1. After adjusting the doors, please insert the
supplied fastener ( 6 ) using a pliers ( 5 ) in the gap
between the hinge-grommet ( 7 ) and the lower
hinge ( 8 ). The number of fastener you’ll need to
insert depends on the gap.
between the hinge-grommet ( 7 ) and the lower
hinge ( 8 ). The number of fastener you’ll need to
insert depends on the gap.
2 fastener are enclosed with the refrigerator.
The thickness of each fastener is 0.04”.
The thickness of each fastener is 0.04”.
ADJUSTING THE FREEZER DRAWER
LEVEL
LEVEL
1. Locate the height-adjuster ( 1 ) in the freezer
drawer. Unscrew the 8 Phillips screws ( 2 ) slightly
to loosen the door.
to loosen the door.
2. Loosen the controller screw ( 3 ) with a Phillips
screwdriver(+).
3. Find the best level to align the door slope.
•
•
After adjustment, tighten the controller screw ( 3 )
and then philips screws.
and then philips screws.
CHECKING THE WATER DISPENSER
LINE
LINE
A water dispenser with a fi lter is one of the helpful
features on your new refrigerator. To help promote
better health, the water fi lter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need to
purchase a water purifying system to do that.
In order for the ice maker to operate properly, a water
pressure of 20~125 psi is required.
Under normal conditions, a 170 cc (5.75 oz.) cup can
be fi lled in about 10 seconds.
If the refrigerator is installed in an area with low water
pressure (below 20psi), you can install a booster pump
to compensate for the low pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator is
properly fi lled. To do this, press the water dispenser
lever until the water runs from the water outlet.
features on your new refrigerator. To help promote
better health, the water fi lter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need to
purchase a water purifying system to do that.
In order for the ice maker to operate properly, a water
pressure of 20~125 psi is required.
Under normal conditions, a 170 cc (5.75 oz.) cup can
be fi lled in about 10 seconds.
If the refrigerator is installed in an area with low water
pressure (below 20psi), you can install a booster pump
to compensate for the low pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator is
properly fi lled. To do this, press the water dispenser
lever until the water runs from the water outlet.
Water line installation kits are available at
extra cost from your dealer. We recommend
using a water line installation kit that contains
copper tubing and ¼” compression nut.
extra cost from your dealer. We recommend
using a water line installation kit that contains
copper tubing and ¼” compression nut.
Freezer Drawer
Adjustment part
Adjustment part
1
2
3
Example) The slope is about 0.08inch (2mm) as shown below.
Example) The slope is about 0.08inch (2mm) as shown below.
- Rotate the height adjuster to -2.0 to reduce the door slope.
- Rotate the height adjuster to -2.0 to reduce the door slope.
- Rotate the height adjuster to -2.0 to reduce the door slope.
Slope
Slope
Reference
Reference
plane
plane
DA68-01922A.indb 10
DA68-01922A.indb 10
2013.3.4 1:32:39 PM
2013.3.4 1:32:39 PM