Справочник Пользователя для Creda Cooker
INSTALLATION
UNPACKING
After unpacking your cooker, make sure that you remove all the packing
from the oven and grill, and any stickers from the oven door and the hob.
Examine your cooker for any damage, particularly the hob glass. Make
sure there are no chips or cracks. If there is any damage to your cooker or
anything is missing, please contact your supplier for advice. If the hob is
cracked the cooker must not be connected to the supply, and no part
of it may be used.
from the oven and grill, and any stickers from the oven door and the hob.
Examine your cooker for any damage, particularly the hob glass. Make
sure there are no chips or cracks. If there is any damage to your cooker or
anything is missing, please contact your supplier for advice. If the hob is
cracked the cooker must not be connected to the supply, and no part
of it may be used.
SITING / MOVING THE COOKER
(See Fig. 1)
Your cooker is heavy, so be careful when moving or positioning it. Do not
try to move the cooker by pulling on the doors or handles.
Movement of your cooker is most easily achieved by lifting the front
as follows. Open the Grill/Oven door sufficiently to allow a comfortable grip
on the underside front edge of the oven roof, avoiding any grill elements or
oven interior furniture. Great care should be taken when moving your cooker
to avoid damage to soft floor coverings. Your Creda cooker is designed to fit
between 600mm deep cabinets, spaced a minimum of 550mm apart. It can
also be used freestanding, with a cabinet to one side, in a corner setting or
with its back to a wall.
try to move the cooker by pulling on the doors or handles.
Movement of your cooker is most easily achieved by lifting the front
as follows. Open the Grill/Oven door sufficiently to allow a comfortable grip
on the underside front edge of the oven roof, avoiding any grill elements or
oven interior furniture. Great care should be taken when moving your cooker
to avoid damage to soft floor coverings. Your Creda cooker is designed to fit
between 600mm deep cabinets, spaced a minimum of 550mm apart. It can
also be used freestanding, with a cabinet to one side, in a corner setting or
with its back to a wall.
The cooker is of type X with regard to protection against overheating of
surrounding surfaces as defined in BS EN60335-2-6: 1991. As such, adjacent
side walls which project above hob level must not be nearer to the cooker
than 150mm (6"). Any overhanging surface or cooker hood should be at least
650mm (25
surrounding surfaces as defined in BS EN60335-2-6: 1991. As such, adjacent
side walls which project above hob level must not be nearer to the cooker
than 150mm (6"). Any overhanging surface or cooker hood should be at least
650mm (25
1
/
2
") above the cooker hob. We do not recommend positioning the
cooker below wall cupboards, as the heat and steam from the cooker may
cause damage to the cupboard and its contents.
cause damage to the cupboard and its contents.
Excess steam from the oven, vents out at the back of the cooker, so the wall
behind the cooker needs to be resistant to the steam or condensation.
behind the cooker needs to be resistant to the steam or condensation.
Whatever the position, remember to leave enough room for the cooker to be
pulled out for cleaning and service, and make sure that the vents in the back
panel of the cooker are not blocked.
pulled out for cleaning and service, and make sure that the vents in the back
panel of the cooker are not blocked.
COOKER HEIGHT
Your cooker must stand on a flat surface so that the hob is perfectly level, and
the cooker is stable and cannot be rocked.
the cooker is stable and cannot be rocked.
If required, a height adjustment kit is available to increase the height to the
hob from 900mm up to a maximum of 914mm. This is available on
application to Creda Spare Parts Department.
hob from 900mm up to a maximum of 914mm. This is available on
application to Creda Spare Parts Department.
5